ZviZZer Thermo Allrounder Pad "Ultra Soft" Thermo Foam Pad (Green) 1 Stück

Remove holograms and seal in deep gloss

What is the ZviZZer Thermo Allrounder Pad Ultra Soft? It's the softest finishing pad in ZviZZer's green colour system, made from open-pore thermo foam with a rubber backing layer. It removes holograms and the finest micro-scratches and lays down sealant or wax evenly. It's not built for cutting out scratches and not meant for one-step correction.

The ZviZZer Thermo Allrounder Pad Ultra Soft is a thermo foam pad from ZviZZer in the softest grade, green. On this Ultra Soft pad an open-pore polishing foam sits on a sealed cushion made of a foam-rubber blend that dampens vibration and carries the rotational force onto the paint without losing any of it. That's how it builds gloss without setting fresh holograms, and spreads sealant or wax streak-free.

• Finish and sealing without new holograms. The open-pore thermo foam cuts nothing — it refines: it pulls out the finest micro-scratches and halos and brings up a deep mirror gloss that really shows on dark paint. A pea-sized blob of polish covers one pad's worth of panel.
• Rubber backing layer for a smooth run. It's the only ZviZZer pad with a foam-rubber layer between the hook-and-loop and the foam. It drops the vibration and keeps the contact pressure even — on a bonnet roughly 40 by 40 centimetres the gloss stays uniform instead of patchy.
• Five sizes for every panel. From Ø 50 mm for mirror caps and swage lines up to Ø 165 mm for the roof and doors, the pad covers every area. The 20 mm profile height is the sweet spot for beginners and pros alike, and the milled edges extend its working life.

Detailing1's tip from the shop: What we see day-to-day, the most common mistake with an ultra-soft pad is dry scrubbing at too high a speed. With no film of polish, the open-pore foam rubs on the paint, builds up heat and sets exactly the holograms it's supposed to remove — we reproduced that in a test on soft black paint. Keep the pad damp, work at a moderate speed and tap it out every two or three sections. A clean, lightly dampened pad finishes better than a clogged one.

Little polish, keep it damp and work it up to high gloss

You work the Ultra Soft pad with a pea-sized blob of finishing polish at a moderate speed until the polish film goes clear and the mirror gloss stands.

By colour and grade it pairs with the green UC 1000 finishing polish, which pulls out the finest swirls and seals in the same pass. Step up one grade of bite with the yellow soft pad when there are still visible holograms after a cutting step. Work in sections of about 40 by 40 centimetres.

Keep the pad clean: after two or three sections, tap out the polish dust or switch to a fresh pad. A clogged pad just smears and won't build any more gloss. You can clean it with a brush, compressed air or in the wash at 30 to 40 degrees — then air-dry it, never in the dryer.

Finish and sealing yes, scratch correction no

The Ultra Soft pad is built for the last step — holograms gone, gloss in, coating laid down evenly. It deliberately doesn't correct, because the soft grade soaks up the cutting power of any polish.

That's exactly its strength when jewelling dark, soft paint and when machine-applying coatings, where a harder pad would drag streaks. Over the rubber backing layer it runs smooth enough that even beginners can pull off a clean mirror.

The limits are clear: when there are scratches or swirls in the paint, reach first for a harder pad from the polishing pad category with a cutting or one-step polish, and only then bring in the Ultra Soft pad as the finish. If you want to correct and shine in a single pass, the medium-hard orange pad is the better call — on the green pad the correction just won't happen.

For the finishing polisher, not the quick reconditioner

The Ultra Soft pad is the right call when you want that last percent of depth after correction, or when you need to lay a coating down mirror-smooth.

It's less suited to the quick reconditioner who wants to be done in one pass: with no cut, every defect stays visible. If you regularly work from scratch all the way to a mirror, you're better off with the graded ZviZZer pad system from Ultra Hard to Ultra Soft than with a single pad — each colour a hardness, each hardness a job.

The one trick no manufacturer writes down: wash a new pad out once and squeeze it dry before you start. Otherwise factory residue in the fresh foam spreads through the first layer and leaves a fine haze on exactly the dark paint the Ultra Soft pad is meant to make shine.

Anwendung des ZviZZer Thermo Allrounder Pad Ultra Soft

Vom korrigierten Lack zum versiegelten Spiegelglanz

Das Ultra Soft Pad kommt nach der Korrektur zum Einsatz. Der Lack sollte sauber und entfettet sein, damit kein Polieröl den echten Glanz vortäuscht und Reste keine Schlieren ziehen.

Eine erbsengroße Menge Finish-Politur auf das leicht angefeuchtete Pad geben, bei moderater Drehzahl ohne Druck auf der Fläche verteilen und ausarbeiten, bis der Polierfilm klar wird und ein tiefer Spiegelglanz steht. Farblich und in der Stufe passt die grüne Finish-Politur UC 1000.

In Abschnitten von etwa 40 mal 40 Zentimetern arbeiten und das Pad nach zwei bis drei Abschnitten ausklopfen oder wechseln. Stehen nach einem Schleifschritt noch sichtbare Hologramme, eine Stufe griffiger mit dem gelben Soft-Pad vorarbeiten und mit dem Ultra Soft Pad finishen.

Zum Versiegeln das Coating oder Wachs erbsengroß aufnehmen und mit dem weichen Schaum dünn und gleichmäßig auftragen. Genau hier spielt das Pad seine Stärke aus, weil ein härteres Pad die Versiegelung verschmieren würde.

Hinweise: Das Ultra Soft Pad trägt nichts ab und korrigiert keine Kratzer oder Swirls, dafür ist ein härteres Pad aus der Polierpad-Kategorie mit einer Schleif- oder One-Step-Politur nötig. Nie trocken schrubben, sonst staut der offenporige Schaum Hitze und setzt neue Hologramme. Reinigen mit Bürste, Druckluft oder Wäsche bei 30 bis 40 Grad, danach lufttrocknen, nicht in den Trockner. Trocken und sauber lagern, ein gerissenes oder dauerhaft verklebtes Pad ersetzen.