ZviZZer Thermo Cone Pad "Soft" Thermo Foam Pad (Yellow) 1 Stück

Polish tight spots and edges hologram-free

What is the ZviZZer Thermo Cone Pad Soft? A small, cone-shaped polishing pad made of open-cell thermo foam with a hook-and-loop back, marked Yellow in the colour system as the soft grade. The tapered tip polishes corners, edges and the areas around badges that a flat pad can't reach. Not for large panels like doors or bonnets, and not for polishing out deep scratches.

ZviZZer Cone Pad Soft is a cone-shaped polishing pad from ZviZZer made of open-cell thermo foam, marked Yellow in the five-grade colour system and therefore the soft grade. Above the hook-and-loop face sits a dimensionally stable thermo foam that doesn't go soft under friction, so it keeps the cutting power constant. The tapered shape drives that cutting power straight into corners and along edges, where a round flat pad runs out. The pad runs on hook-and-loop on a small backing plate.

• Cone tip for the corners a flat pad misses. The tapered shape polishes around badges, at mirror bases, in body creases and along bumper edges. Exactly where a round pad of 140 or 165 mm can't reach, the small Ø 30 mm tip works cleanly right into the radius. So you don't get a dull edge left next to the polished rest.
• Constant cutting power from thermo foam. The open-cell thermo foam stays dimensionally stable and doesn't go soft under heat, unlike a standard foam. That's why the soft pad leaves no holograms even at the small tip. According to the manufacturer the tear-resistant foam lasts up to 6 times longer than a conventional pad.
• Soft as the gentle finishing grade in three hardnesses. The Cone Pad comes in 3 hardnesses, Hard, Medium and Soft, and Yellow is the soft one. It cuts very little and refines rather than removing material. That's how you pull the last percent of gloss from tight spots without risking fresh marring there.

Detailing1's tip from the shop: The most common mistake with a small cone pad is too much pressure and rpm on that tiny face. The Ø 30 mm tip builds heat in one spot fast, then the polish dries on and you're left with a haze instead of gloss. Little product, low rpm, small movements. Day-to-day in Nordhorn we got the area around a rear badge clean on black paint, where the flat 140 mm pad only came within 2 centimetres of the badge.

The tip into the corner, the flank against the edge

You work the Cone Pad Soft spot by spot into the tight areas: the tip into the corner, the flank of the cone against the edge, with a fine polish and low rpm.

Day-to-day, the yellow ZviZZer Cone Pad Soft is the partner of the FC 2000 finishing polish in the same yellow grade. You put a pea-sized blob on the cone face, spread it at around 1,000 rpm and then work it out at 1,500 rpm max with light pressure until the film goes clear. Set the cone on hook-and-loop onto a small backing plate, say on a mini polisher or a cordless detail polisher.

Keep the pad clean and cool: never push it over the edge of the plate and work with small movements, otherwise the little tip overheats. The big panels next to it you polish with a flat polishing pad of the same hardness; the Cone Pad is only for the spots the flat pad can't reach.

Tight spots yes, whole panels no

The Cone Pad Soft is a detail tool for tight spots in finishing: it cuts little and refines corners and edges rather than working down panels.

Its home turf is everything a round pad leaves out: the area around badges and door handles, mirror bases, body creases, bumper edges and vent slots. There it removes fine holograms and builds gloss, in keeping with the soft yellow grade. On sensitive paint it stays gentle, because the thermo foam keeps the cutting power constant and doesn't tear out.

The limits are clear: at Ø 30 mm it's no pad for doors or bonnets, that takes forever and you'd grab a flat pad. And a soft pad corrects no deep scratches. If there's a light defect in a tight spot, you reach for the harder Cone Pad Medium in Orange with more cut. And a pad on its own cuts nothing: the effect only comes from pad hardness and polish grit working together.

For the detail, not for the panel

The ZviZZer Cone Pad Soft is the right call when, after polishing the panels, the tight spots are still dull and you want to bring them up to the same gloss.

It's less suited as your only pad for a whole detail, because for panels it simply lacks the size. It's the add-on to the flat pad, not the replacement. Anyone who takes tight spots seriously keeps at least one Cone Pad in the right hardness next to the big pads, here the soft yellow grade for finishing.

One detail that decides the lifespan and that the fewest people bother with: wash out the little cone face right after polishing, before the polish hardens inside it. On that tiny face especially, hardened residue glues up the open foam straight away, then the tip won't take any more polish and the cone is done. Air-dry it lying flat, not in the sun. That way the tear-resistant thermo foam stays dimensionally stable and you really do get the six-fold lifespan out of it.

Anwendung des ZviZZer Thermo Cone Pad Soft

Mit der Kegelspitze in Ecken und an Kanten finishen

Das Cone Pad Soft ist ein Detailwerkzeug für den Finish-Schritt an engen Stellen, nachdem die Fläche mit einem normalen Pad poliert ist. Setze den Ø 30 mm kleinen Kegel über Klett auf einen passenden kleinen Stützteller, etwa an einer Mini-Poliermaschine oder einem Akku-Detailpolierer.

Gib eine erbsengroße Menge einer feinen Finish-Politur auf die Kegelfläche, tupfe sie an der engen Stelle an und verteile sie bei niedriger Drehzahl. Dann mit leichtem Druck und kleinen Bewegungen ausarbeiten, bis der Polierfilm klar wird und Glanz steht. Die Spitze führst du in die Ecke, die Flanke des Kegels an die Kante.

Arbeite Spot für Spot: um ein Emblem herum, an einem Spiegelfuß, in einer Sicke. Für die großen Flächen daneben nimmst du ein flaches Polierpad derselben Härte. Drück das Pad nie über den Tellerrand und halte die Drehzahl niedrig, sonst überhitzt die kleine Schaumspitze.

Wasch das Pad direkt nach dem Polieren aus, bevor die Politur im offenen Schaum aushärtet, und lass es liegend an der Luft trocknen, nicht in der Sonne. So bleibt der Thermo-Schaum formstabil und behält seine Aufnahme.

Hinweise: Das gelbe Cone Pad Soft ist die weiche Finish-Stufe und trägt wenig ab. Für leichte Defekte an engen Stellen nimmst du das orangefarbene Cone Pad Medium, das Cone Pad gibt es nur in den drei Härten Hard, Medium und Soft. Ein Pad allein korrigiert nichts, die Schleifwirkung entsteht erst mit dem Politur-Korn zusammen. Wegen der kleinen Ø 30 mm Fläche ist es ein Spot-Werkzeug, keine Lösung für Türen oder Hauben. Trocken und sauber lagern, Schaum vor Lösemitteln und scharfen Reinigern schützen.