ZviZZer Thermo Mini Pad "Ultra Soft" Thermo Foam Pad (Green) 10 Stück

The finest finish where no big pad will reach

What is the ZviZZer Thermo Mini Pad Ultra Soft? A tiny polishing pad made from open-cell thermo foam with a hook-and-loop backing, in the softest grade Green, as a 10-pack in Ø 15 and Ø 25 millimetres. It polishes out the faintest holograms and lays down sealant in the tightest spots where no normal pad will fit. It's not a cutting pad and it's not meant for whole panels.

The ZviZZer Thermo Mini Pad Ultra Soft is a spot polishing pad from ZviZZer made of open-cell thermo foam with a hook-and-loop back, in Ø 15 and Ø 25 millimetres as a 10-pack. The colour Green marks the softest of the five hardness grades, so pure finishing with no real cut. The thermo foam pulls the friction heat away, holds its shape and hardness, and makes the Mini the one to grab for badges, lettering and tight contours.

• Ø 15 and 25 mm for the tightest spots. The Mini reaches pinpoint what even a 50 mm pad can't: lettering, door-handle recesses, mirror bases, narrow trim strips and headlight corners. Two diameters in the 10-pack cover every small contour without you catching an edge.
• Softest of the 5 grades for pure finish with no cut. Green is grade 5 of 5 in the ZviZZer system and removes next to nothing. It polishes out the faintest holograms and halos and builds deep gloss, ideal as the last step on dark, soft clear coats where a harder pad would put in its own streaks.
• Thermo foam holds the cut and lasts 5 to 6 times longer. The open-cell thermo foam stays dimensionally stable under heat instead of going soft, and according to the maker lasts 5 to 6 times longer than standard foam. On the small Mini plate with its high rim speed, that heat stability is exactly what counts.

Detailing1's tip from the shop: The most common mistake with a Mini pad is too much speed. A Ø 15 mm pad has a far higher rim speed than a big one at the same rpm, the tiny foam overheats in seconds and burns a hologram ring into dark paint. Wind the machine down, work with little product and keep the pad moving. On a black 2026 clear coat around the fuel-filler cap one pass did it for us, where at full speed we'd first worked a dull patch into it.

Small plate little product low speed

You press the Mini centred onto the matching hook-and-loop backing plate, drop on a bit of finishing polish and work it out at low speed with light pressure until the film goes clear.

Because the pad radius is so small, you need a lot less speed than with a big pad, otherwise the rim speed runs away from you. One drop of polish covers several spots. The Mini is colour-matched to the green UC 1000 Ultrafine Cut, the two of them making up the finest finishing and sealing step.

Keep the pad clean and damp: on that tiny face, polishing dust clogs it fast, and a clogged Mini just smears and stops building gloss. Never let it run dry. Guided over your thumb joint you get into badges and pillar edges where a plate pad keeps catching somewhere.

Finest finish yes correction and panels no

The Mini Ultra Soft is built for the last percent on small spots and by design removes nothing, which is why it doesn't correct defects but only refines and seals.

Its strength is spot work: the faintest holograms on badges, a seal around lettering, the high gloss in a door-handle recess. As the softest pad in the series it finishes where a medium or hard pad would be too coarse and the defect is only cosmetic anyway.

The limits are honest. If you need to take out light holograms before the finish, then the grade grippier Mini Pad Soft in Yellow first, the Ultra Soft only at the end. If you're polishing a whole door or bonnet, the Mini is the wrong call, for that you grab a big pad from our polishing pads and sanding sponges. Real scratches only come out with a harder pad and a cutting polish anyway.

For detail work not for the whole body

The Mini earns its keep for anyone who, after polishing the panels, wants to finish the small spots cleanly that no normal pad can reach.

Because the cutting power is steered partly through the pad hardness, the green Mini is the finest building block of a stepped system: you correct the panel with bigger, harder pads and bring in the Ultra Soft spot by spot for the finish and the sealing on the contours. You pick between the two diameters of Ø 15 and 25 millimetres by spot, the smaller one for badges and lettering, the bigger one for recesses and narrow trim.

Less suited is the Mini for beginners who've never worked tight contours with a machine. On such a small face a pad forgives little, and a hologram ring is quickly worked in if the speed is off. If you're unsure, practise first on an inconspicuous large panel.

The one point most people underrate: with the Mini the 10-pack isn't a bulk discount, it's the concept. The tiny pads clog faster than big ones and aren't endlessly washable, so on detail work you'd rather swap to a fresh Mini once more than keep smearing with a gummed-up one that stopped building gloss long ago.

Anwendung des ZviZZer Thermo Mini Pad Ultra Soft

Vom kleinen Stützteller bis zum sauberen Spot-Finish

Die Fläche muss vorbereitet sein: gewaschen, dekontaminiert und die grobe Korrektur mit größeren Pads schon erledigt. Drücke das Mini mittig auf den passenden Klett-Stützteller mit 15 oder 25 Millimeter Aufnahme, damit es rund läuft.

Gib einen Tropfen UC 1000 Ultrafine Cut auf das Pad und tupfe ihn bei stehender Maschine auf die Stelle. Arbeite die Politur bei niedriger Drehzahl mit leichtem Druck aus, bis der Polierfilm klar wird. Wegen des kleinen Radius brauchst du deutlich weniger Drehzahl als bei einem großen Pad, sonst läuft die Randgeschwindigkeit davon und der Schaum überhitzt.

Halte das Mini sauber und feucht. Auf der winzigen Fläche setzt sich Polierstaub schnell fest, ein zugesetztes Pad schmiert nur. Lass es nie trocken laufen und wechsle bei Verklebung auf ein frisches aus dem 10er-Pack. Für leichte Hologramme vor dem Finish nimmst du das eine Stufe griffigere Mini Pad Soft in Gelb.

Hinweise: Das Mini Ultra Soft ist die weichste Stufe und trägt nichts ab, es ist für Finish und Sealing an engen Stellen gedacht, nicht für die Korrektur und nicht für ganze Flächen. Eine ganze Tür oder Haube polierst du mit einem großen Pad. Auf sehr weichen schwarzen Lacken nur mit niedriger Drehzahl arbeiten, sonst setzt selbst das weiche Mini einen Hologramm-Ring. Nach Gebrauch mit lauwarmem Wasser oder Pad-Reiniger auswaschen, gut ausdrücken und liegend lufttrocknen lassen, nicht knicken und nicht heiß trocknen.