{"title":"Beleuchtung","description":"\u003ch2 id=\"speakable-headline\"\u003eBeleuchtung\u003c\/h2\u003e\n\u003cp id=\"speakable-definition\"\u003e\u003cstrong\u003eBeleuchtung\u003c\/strong\u003e: Leuchten machen Arbeitsbereiche und feine Oberflächenspuren sichtbar. Hand- und Stirnlampen erreichen enge Stellen, Strahler beleuchten größere Bereiche und Kontrollleuchten zeigen feine Spuren.\u003c\/p\u003e\n\u003cp\u003eLichtverteilung, Position und Versorgung werden nach der Aufgabe gewählt, nicht nur nach der maximalen Helligkeit.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/es\/collections\/lackkontrollleuchten\"\u003eLackkontrollleuchten\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/es\/collections\/arbeitsleuchten\"\u003eArbeitsleuchten\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","products":[{"product_id":"flex-sf150p-swirl-finder","title":"\"SF 150-P\" Swirl Finder","description":"\u003ch2\u003eFLEX SF 150-P Swirl Finder — lámpara de inspección pro para swirls, hologramas y defectos de pintura\u003c\/h2\u003e\n\u003cblockquote\u003e\n\u003cp\u003e\u003cem\u003e¿Qué es el FLEX SF 150-P Swirl Finder? El FLEX SF 150-P es una lámpara de inspección profesional pensada para el control de la pintura — una lámpara spot con haz dirigido que revela swirls, hologramas, arañazos y defectos finos de la pintura, antes y después del pulido.\u003c\/em\u003e\u003c\/p\u003e\n\u003c\/blockquote\u003e\n\u003chr\u003e\n\u003cp\u003eEl mejor pulido no sirve de nada si no lo puedes ver. El \u003cstrong\u003eFLEX SF 150-P Swirl Finder\u003c\/strong\u003e es la herramienta que marca la diferencia entre un pulido bueno y uno profesional: una lámpara de inspección que revela swirls, hologramas y arañazos finos en la pintura, invisibles con luz normal. Pulir sin swirl finder es pulir a ciegas.\u003c\/p\u003e\n\u003cp\u003eEl \u003cstrong\u003eFLEX SF 150-P\u003c\/strong\u003e no es una linterna cualquiera — es una herramienta de inspección dedicada al trabajo de pintura, que con un haz estrecho y dirigido, en un ángulo concreto, saca a la luz la estructura de la superficie. Los swirls y los hologramas son arañazos finos en el barniz que, bajo luz rasante, aparecen como dibujos claros. El SF 150-P crea justo esa luz rasante — sobre una mancha de luz bien definida, lo bastante nítida para la inspección de detalle.\u003c\/p\u003e\n\u003cp\u003eComo herramienta de inspección, el SF 150-P completa todo el sistema de pulido FLEX: lo usas antes de pulir para evaluar los defectos, durante el proceso para seguir el avance y después de cada paso para verificar el resultado. Un protocolo de pulido sin herramienta de inspección es una suposición — con el SF 150-P se convierte en un control de calidad medible.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eHaz spot dirigido para una visibilidad precisa de swirls y hologramas — el ojo del detailer profesional.\u003c\/strong\u003e El SF 150-P proyecta una mancha concentrada con un ángulo de incidencia definido, que saca los arañazos finos y los swirls del barniz como dibujos claros. Ese haz spot es la base técnica de la inspección pro de la pintura: una luz difusa no resaltaría las estructuras finas — el spot concentrado las hace inconfundibles, incluso para un ojo poco entrenado.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHerramienta de inspección pro para el antes y el después del pulido — control de calidad a nivel profesional.\u003c\/strong\u003e El SF 150-P hace medible el avance del pulido: antes del primer paso de cut muestra el tipo y la profundidad de los defectos. Después de cada paso te dice si ha quitado los defectos del todo o si hace falta más trabajo. Ese bucle de feedback es el corazón del pulido pro — sin él, trabajas a lo loco.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiseño compacto y manejable para el día a día — siempre a mano para un control rápido.\u003c\/strong\u003e El formato compacto hace del SF 150-P el compañero ideal en el pulido diario: a mano en el banco o en el mandil portaherramientas, rápido de coger para un control intermedio, y lo dejas en un momento cuando no lo necesitas. Sin trípode aparatoso, sin montaje engorroso — lo coges, lo usas, listo.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003chr\u003e\n\u003cblockquote class=\"praxistipp\"\u003e\n\u003cp\u003e\u003cstrong\u003eLo que vemos en el día a día:\u003c\/strong\u003e Para sacarle todo el partido al FLEX SF 150-P Swirl Finder: oscurece la zona de inspección o trabaja en las zonas de sombra — la luz del día que entra de lado compite con el haz spot y se come la visibilidad de los swirls. Mantén la mancha de luz en un ángulo rasante de 30–45° respecto a la pintura y muévela despacio por la superficie que estás revisando — los swirls y los hologramas aparecen como dibujos claros, circulares o en estrella. Después del paso de finish, revisa la superficie con el SF 150-P desde varios ángulos: un buen resultado queda impecable desde cualquier ángulo, sin ningún holograma escondido solo con una incidencia de luz concreta.\u003c\/p\u003e\n\u003c\/blockquote\u003e\n\u003chr\u003e\n\u003ch3\u003ePor qué la inspección lo es todo — hacer visibles swirls y hologramas\u003c\/h3\u003e\n\u003cp\u003eLos swirls son arañazos finos y circulares en el barniz, provocados por métodos de lavado inadecuados, mala técnica de pulido o un polish malo. Bajo el sol directo o bajo un haz dirigido como el del \u003cstrong\u003eFLEX SF 150-P Swirl Finder\u003c\/strong\u003e se ven bien — con la luz indirecta normal, en cambio, apenas. Eso explica por qué el cliente queda contento con un pulido bajo luz normal, y luego vuelve a ver los swirls el primer día de sol.\u003c\/p\u003e\n\u003cp\u003eLos hologramas son otro tipo de defecto: salen de una técnica de pulido incorrecta, demasiadas revoluciones o una combinación pad-polish equivocada al pulir a máquina. A diferencia de los swirls, los hologramas no son circulares, sino que muestran un dibujo uniforme, a rayas, que sigue el recorrido del pad. Bajo el haz spot del SF 150-P se reconocen bien, y tienen que desaparecer del todo antes del paso de finish — si no, el resultado final no queda pro, por mucho trabajo que le hayas metido al pulido.\u003c\/p\u003e\n\u003cp\u003ePara un detailer con experiencia, inspeccionar con el SF 150-P no es el final del control de calidad — es el principio: lo que encuentras marca el protocolo. Los swirls profundos piden el paso de cut con el PP-C; los hologramas finos de una pasada anterior salen con el PP-M o el PP-F; una película grasienta en la superficie no es un arañazo sino un problema de limpieza, y pide otra cosa. Inspeccionar con el SF 150-P hace visible esa diferencia — y evita el error más caro del detailing: el protocolo equivocado para el tipo de defecto equivocado.\u003c\/p\u003e\n\u003cp\u003ePara quien empieza en el detailing, el SF 150-P es una herramienta de aprendizaje: enseña lo que consigue una buena técnica y lo que deja una mala. Si controlas a menudo con el SF 150-P y valoras el resultado tras cada paso, en unas pocas sesiones aprendes sobre calidad de pulido más que probando a lo loco sin herramienta de feedback.\u003c\/p\u003e\n\u003ch3\u003eEl SF 150-P en un workflow de pulido pro — la inspección como fase fija\u003c\/h3\u003e\n\u003cp\u003eUn protocolo de pulido pro con el \u003cstrong\u003eFLEX SF 150-P Swirl Finder\u003c\/strong\u003e integrado es así: entra el coche, limpieza gruesa, y luego primera inspección con el SF 150-P — registro sistemático de todos los defectos de la pintura, notas de los puntos problemáticos, protocolo de pulido fijado. Esa primera inspección es la base para el presupuesto al cliente y para tu propia organización: ¿cuántos pasos hacen falta? ¿Qué zonas piden más trabajo?\u003c\/p\u003e\n\u003cp\u003eDurante el pulido, el SF 150-P sale después de cada paso: tras el cut con el \u003ca href=\"\/es\/products\/flex-pp-c-cut-polierpad\"\u003ePP-C\u003c\/a\u003e compruebas que han salido todos los arañazos profundos antes de empezar con el compound. Tras el compound con el \u003ca href=\"\/es\/products\/flex-pp-m-universal-polierpad\"\u003ePP-M\u003c\/a\u003e compruebas que han desaparecido todos los hologramas del cut. Solo cuando el SF 150-P confirma que ya no queda ningún holograma, empiezas el finish con el \u003ca href=\"\/es\/products\/flex-pp-f-finish-polierpad\"\u003ePP-F\u003c\/a\u003e.\u003c\/p\u003e\n\u003cp\u003eEl control de calidad final antes de devolver el coche al cliente es el último trabajo del SF 150-P: inspección sistemática de cada pieza de carrocería bajo el haz spot — ni un holograma, ni un swirl, ni un punto pasado por alto. Solo cuando esa inspección final sale limpia, el coche está listo para entregar. En este workflow el SF 150-P no es opcional, sino la última puerta de calidad antes de la entrega.\u003c\/p\u003e\n\u003ch3\u003eEquipamiento técnico del SF 150-P — temperatura de luz, foco y duración de uso\u003c\/h3\u003e\n\u003cp\u003eEl rendimiento de una lámpara de inspección no depende solo del brillo — los detalles técnicos del haz deciden lo bien y lo fiable que se ven los swirls. El \u003cstrong\u003eFLEX SF 150-P\u003c\/strong\u003e lleva una temperatura de color alta, en el rango del blanco luz de día, cercana al sol natural. Es decisivo: con luz blanco cálido muchos swirls apenas se ven, porque la temperatura de color rojiza tapa los reflejos de luz dispersa de los arañazos. El blanco luz de día con un CRI alto hace esos reflejos nítidos y con buen contraste.\u003c\/p\u003e\n\u003cp\u003eEl spot dirigido del SF 150-P crea un límite nítido entre la zona iluminada y la que queda a oscuras. Ese límite nítido cuenta para la inspección de swirls: los hologramas y los swirls se ven mejor justo en la línea entre el spot claro y el fondo oscuro. Si mueves esa zona de transición de forma sistemática por la superficie, encuentras todos los defectos — también los que en el centro del spot resaltarían menos.\u003c\/p\u003e\n\u003cp\u003ePara un uso prolongado, la autonomía de la lámpara es un factor real. El SF 150-P está pensado para el uso pro del día a día — fabricación sólida, luz de sobra para una vuelta completa al coche sin que baje. El formato manejable permite currar sin cansarse, incluso en fases de inspección más largas.\u003c\/p\u003e\n\n\u003ch3\u003eEl SF 150-P frente a otras opciones — lámpara de inspección dedicada vs. linterna y luz del día\u003c\/h3\u003e\n\u003cp\u003eEl SF 150-P no es la única luz con la que ves los swirls — pero es la más eficaz para el día a día. Ponlo al lado de las alternativas habituales y ves por qué una lámpara de inspección dedicada es insustituible.\u003c\/p\u003e\n\u003cp\u003eLa luz del día muestra bien los swirls — pero solo bajo sol directo y con el ángulo correcto. En interior el sol directo hay poco, y fuera depende del tiempo, la hora y cómo esté orientado el coche. Si haces que tu juicio sobre la calidad del pulido dependa solo del sol, no puedes controlar de forma sistemática ni repetible.\u003c\/p\u003e\n\u003cp\u003eLas linternas normales no dan una luz rasante lo bastante dirigida para la inspección de swirls. Fuente demasiado difusa, franja del espectro equivocada, sin ángulo definido — el resultado es una imagen poco fiable que unas veces muestra los swirls y otras no, según cómo la sujetes por casualidad. El SF 150-P quita ese azar de en medio: siempre el mismo tipo de luz, siempre el mismo ángulo, siempre resultados repetibles.\u003c\/p\u003e\n\u003cp\u003eLas lámparas de espectro completo como la \u003ca href=\"\/es\/products\/flex-dwl-2500-vollspektrum-leuchte\"\u003eFLEX DWL 2500 lámpara de espectro completo\u003c\/a\u003e son una iluminación de ambiente estupenda para todo el espacio, pero no sustituyen a una lámpara de inspección de mano. La luz de espectro completo en el techo muestra los swirls en toda la superficie — el SF 150-P los muestra en detalle en el punto exacto que estás revisando. Las dos herramientas se complementan: luz de espectro completo para la impresión general, SF 150-P para el control de detalle dirigido. Quien tiene las dos, tiene el control de calidad completo.\u003c\/p\u003e\n\u003ch3\u003eComprar el FLEX SF 150-P — la inversión que mejora cada pulido\u003c\/h3\u003e\n\u003cp\u003ePor 47,48 € el Swirl Finder es una de las compras más baratas del maletín de un detailer pro — y a la vez una de las más eficaces. Ningún pad caro, ninguna mejora de máquina complicada mejora la calidad del pulido tan directamente como la herramienta que hace visible esa calidad.\u003c\/p\u003e\n\u003cp\u003ePara un detailer pro el SF 150-P no es un extra opcional, sino equipamiento obligatorio. Si ofreces servicios de pulido y no usas lámpara de inspección, te expones a reclamaciones de clientes que ven los hologramas al sol — aunque tu propio control saliera limpio. El SF 150-P es tu seguro contra eso: los hologramas los pillas tú, no el cliente en el aparcamiento.\u003c\/p\u003e\n\u003cp\u003eComo parte de un set de pulido FLEX completo, recomendamos el SF 150-P junto a los pads \u003ca href=\"\/es\/products\/flex-pp-c-cut-polierpad\"\u003ePP-C\u003c\/a\u003e, \u003ca href=\"\/es\/products\/flex-pp-m-universal-polierpad\"\u003ePP-M\u003c\/a\u003e y \u003ca href=\"\/es\/products\/flex-pp-f-finish-polierpad\"\u003ePP-F\u003c\/a\u003e, como pieza imprescindible del workflow de aseguramiento de calidad. Si combinas estas cuatro herramientas, tienes un sistema completo para la corrección de pintura pro con control de calidad integrado — desde el primer arañazo hasta una inspección final impecable y verificada.\u003c\/p\u003e\n","brand":"FLEX","offers":[{"title":"SF 150-P \"463302\"","offer_id":57377617740111,"sku":"D1-FLEX-463302","price":39.89,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0800\/3272\/7375\/files\/flex-sf-150-p-swirl-finder-sf-150-p-463302-463302.png?v=1775059236"},{"product_id":"flex-dwl25001218-led-vollspektrum-leuchte","title":"\"DWL 2500 12\/18\" Lámpara LED de Espectro Completo (12\/18V)","description":"\u003ch2\u003eFLEX DWL 2500 12\/18 Full-Spectrum Light — 3000 Lumens, CRI RA 96 and All-Daylight for Professional Paint Inspection\u003c\/h2\u003e\n\u003cblockquote\u003e\n\u003cp\u003e\u003cem\u003eWhat is the FLEX DWL 2500 12\/18 Full-Spectrum Light? The FLEX DWL 2500 is a battery-powered LED full-spectrum light with 3,000 lumens, CRI RA 96, and stepless color temperature adjustment from 2,500K to 6,500K — designed for professional paint inspection, hologram detection, and color matching in detailing.\u003c\/em\u003e\u003c\/p\u003e\n\u003c\/blockquote\u003e\n\u003chr\u003e\n\u003cp\u003eTo detect scratches, holograms, and paint defects, you need the right light. Not just bright enough, but also color-accurate enough — because many defects are simply invisible under incorrect light. The \u003cstrong\u003eFLEX DWL 2500 Full-Spectrum Light\u003c\/strong\u003e has been developed precisely for this requirement: a professional inspection light that, with CRI RA 96 and up to 3,000 lumens of work light, makes even the finest surface flaws, polishing marks, and color deviations visible.\u003c\/p\u003e\n\u003cp\u003eThe light is part of the \u003ca href=\"\/es\/products\/flex-ap18-akku-pack-18v\"\u003eFLEX 18V battery system\u003c\/a\u003e and can be operated with 12V and 18V battery packs — a single device that can be flexibly used in the detailing station, for mobile applications, and on the vehicle. Thanks to its IP67 protection class, it is also suitable for use during car washes, polishing work with a water spray bottle, or in humid environments. The integrated USB power bank function also charges smartphones and tablets — practical for long detailing sessions where the phone cannot run out of battery.\u003c\/p\u003e\n\u003cp\u003eWith up to 30 hours of runtime at 300 lumens (economy mode) or full power for intensive inspection phases: it covers both operating modes, making it the most versatile light in the FLEX detailing portfolio. The flexible light intensity control makes it equally suitable as a continuous work light for the entire workday or as a focused inspection light for quality control in the final step.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCRI RA 96 — Photo studio level color rendering for maximum defect detection.\u003c\/strong\u003e A Color Rendering Index of RA 96 means that the light renders colors 96% as accurately as natural sunlight. This is crucial for paint inspection: color deviations between body parts, subtle holograms after polishing, and oxidation-related dullness are only reliably detectable under high-quality full-spectrum lighting. Cheap workshop lights with CRI below 80 distort colors and make defects invisible that clearly stand out under the DWL 2500.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAll-Daylight 2,500K–6,500K in 5 stages — Color temperature for every application.\u003c\/strong\u003e The gradual color temperature adjustment allows the light to be precisely matched to the task: Warm white light (2,500K) for evaluating warm-tone paints and metallic colors, neutral white light (4,000K) for general inspection, cool white daylight (6,500K) for detecting holograms and fine polishing marks. What is invisible at 4,000K often clearly catches the eye at 6,500K — and vice versa. This flexibility saves time and increases detection reliability.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIP67 waterproof, USB power bank, and 30h runtime — robust everyday usability.\u003c\/strong\u003e The IP67 protection class makes the DWL 2500 splash-proof and dust-tight — it withstands polishing dust, water sprays, and normal handling in daily detailing. The integrated USB-A interface for the power bank function allows external devices to be charged directly via the light's battery. Up to 30 hours of runtime in economy mode means: For mobile use without access to power outlets, the DWL 2500 is ready for several working days without recharging.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003chr\u003e\n\u003cblockquote class=\"praxistipp\"\u003e\n\u003cp\u003e\u003cstrong\u003ePractical tip from Detailing1:\u003c\/strong\u003e For hologram detection after polishing, we recommend setting the DWL 2500 to 6,500K (daylight) and guiding the light flat at a 30–45° angle over the polished surface. Glancing light makes polishing marks and uneven application visible that remain invisible under direct light. Only when the surface is flawless under this test do you move on to the next step. For final color evaluation, 4,000K is recommended for a neutral reference.\u003c\/p\u003e\n\u003c\/blockquote\u003e\n\u003chr\u003e\n\u003ch3\u003eCRI RA 96 and Full Spectrum — why color rendering is crucial for paint inspection\u003c\/h3\u003e\n\u003cp\u003eThe Color Rendering Index (CRI) is the decisive parameter for professional inspection lights. It describes how accurately a light source reproduces colors compared to natural sunlight (CRI 100). The \u003cstrong\u003eFLEX DWL 2500 Full-Spectrum Light\u003c\/strong\u003e achieves RA 96 — a value that is practically indistinguishable from daylight and is considered a mark of professionalism in the color control industry.\u003c\/p\u003e\n\u003cp\u003eWhat RA 96 means in practice: color deviations between replaced and original body parts after a repair paint job are reliably recognizable under this light. Holograms — the circular pattern that appears when the polishing process has not been completed cleanly — clearly stand out under full-spectrum light, even if they remain invisible under conventional neon light. The finest application marks from finishing pads, oxidation-related dullness at certain angles, differences in clear coat thickness — all of this is recognizable under RA 96 CRI light, making it impossible to overlook poor workmanship.\u003c\/p\u003e\n\u003cp\u003eFor customers who have high-end vehicles detailed, this control reliability is a quality argument: anyone who has worked and inspected with the DWL 2500 can confidently say that the result meets professional standards. And any detailer who delivers without this control step risks receiving complaints that would have been recognizable in the workshop with the right light.\u003c\/p\u003e\n\u003cp\u003eIn practice, the following inspection routine is recommended: first check the polished surface at 6,500K with glancing light (30° angle) for holograms and polishing marks, then at 4,000K for paint uniformity and potential transition zones. Only when both inspections have passed is the result truly ready for acceptance. With the DWL 2500, this routine can be performed quickly and without changing location — simply change the color temperature level, adjust the angle, and you're done.\u003c\/p\u003e\n\u003ch3\u003eAll-Daylight: 2,500K to 6,500K Color Temperature in 5 Stages\u003c\/h3\u003e\n\u003cp\u003eThe All-Daylight function of the DWL 2500 allows the selection of five color temperature levels between 2,500K and 6,500K. This is far more than a technical gimmick — each level has a specific function in the detailing workflow.\u003c\/p\u003e\n\u003cp\u003eWarm white light around 2,500–3,000K is particularly suitable for evaluating warm color tones: bronze, copper, warm silver, certain burgundy and red paints. These tones change their character significantly under cool light and are most accurately judged under warm white illumination. Detailers who work on vehicles with exclusive special colors benefit from this flexibility and can ensure that the color evaluation takes place under nearly natural conditions — not distorted by the cool blue light of a standard workshop lamp.\u003c\/p\u003e\n\u003cp\u003eNeutral white light around 4,000K is the most versatile setting for general work: uniform illumination without color shift, good for the polishing process itself, for pad changes, and for intermediate checks after individual steps. It is also the recommended setting for client consultations at the vehicle — the light is pleasant for the eye and gives the paint and bodywork a realistic, natural appearance.\u003c\/p\u003e\n\u003cp\u003eCool white daylight around 6,000–6,500K is the sharpest instrument for final quality control. Polishing marks, holograms, swirl marks, and paint defects are most clearly visible under this light — the glancing light combined with high color temperature is the best way to declare a paint surface definitively \"finished.\" Anyone who integrates this control step into the acceptance process works with a safety net that cheap tools simply cannot offer.\u003c\/p\u003e\n\u003cp\u003eThe staged switching is deliberately limited to five values — not stepless, but in defined steps. This has a practical advantage: the user can reproducibly access a preferred setting without having to scroll through a spectrum. In everyday use, this means: once learned which level applies to which task — and the DWL 2500 always provides the same reference basis for evaluation.\u003c\/p\u003e\n\u003ch3\u003e3,000 Lumens, IP67, and USB Power Bank — the comprehensive technical features of the DWL 2500\u003c\/h3\u003e\n\u003cp\u003eThe technical equipment of the DWL 2500 is comprehensive and designed for professional continuous operation. The 3,000 lumens in 18V operation are comparable to a very bright office grid lighting panel — enough to create additional contrasts even in brightly lit workshops and make defects visible that disappear in ambient light.\u003c\/p\u003e\n\u003cp\u003eThe IP67 protection class — dust-tight and temporarily submersible up to 1m — makes the light resistant to all normal influences in the detailing workshop: polishing dust, water from spray bottles, sweat, occasional drops onto damp ground. This is not a given for high-performance LED lights in this price range and a clear signal for professional use.\u003c\/p\u003e\n\u003cp\u003eThe integrated USB-A interface for the power bank function is a useful secondary feature: smartphone battery empty during a long outdoor assignment? Simply connect it to the light and continue charging. For mobile detailers who work for several hours without access to power outlets, this is a practical safeguard for communication with customers and for customer service during detailing.\u003c\/p\u003e\n\u003cp\u003eThe light intensity control allows stepless adjustment from 300 to 3,000 lumens. When set to 1,000–1,500 lumens for continuous use as work lighting, a 5.0 Ah battery charge lasts for several hours. For short inspection phases at full power (3,000 lumens), the device consumes more but provides maximum illumination in the shortest possible time. The combination of long runtime and high peak performance makes the DWL 2500 a reliable partner for any duration of use.\u003c\/p\u003e\n\u003ch3\u003eDWL 2500 Comparison — Full-Spectrum Light vs. Conventional Workshop and Photo Area Lights\u003c\/h3\u003e\n\u003cp\u003eStandard workshop lights with CRI 70–80 are sufficient for general work. For professional paint inspection, color matching, and hologram detection, they are unsuitable. The difference is significant: under CRI-80 light, a painted vehicle often looks perfect, even though fine swirl marks are present. Under the \u003cstrong\u003eFLEX DWL 2500 Full-Spectrum Light\u003c\/strong\u003e with RA 96, the same defects clearly stand out — and not just under ideal conditions, but also in a normal workshop situation with ambient light, polishing dust, and variable lighting conditions.\u003c\/p\u003e\n\u003cp\u003eDaylight simulation lights from the photography sector with a fixed color temperature (usually 5,500K) are an alternative but have decisive disadvantages: no battery operation, no IP protection class, no all-daylight range, and generally significantly worse robustness for use in the workshop. They are optimized for photo studio use — not for everyday professional detailing, where the light may occasionally fall to the ground, come into contact with spray water, or run for hours in high-intensity operation.\u003c\/p\u003e\n\u003cp\u003eInexpensive LED spotlights with daylight tint (often advertised as \"daylight\") mislead with bright lumen numbers but often only deliver CRI 75–85. This is sufficient for general lighting, but not for defect detection. Anyone who has compared a polished surface under CRI 96 and directly under CRI 80 will immediately understand the difference: what appears flawless under 80 shows its true defects under 96.\u003c\/p\u003e\n\u003cp\u003eThe \u003cstrong\u003eFLEX DWL 2500 Full-Spectrum Light\u003c\/strong\u003e combines the best of both worlds: photo studio color accuracy in a robust, battery-powered tool housing from the FLEX system. Anyone who uses the \u003ca href=\"\/es\/products\/flex-sf150p-swirl-finder\"\u003eFLEX SF 150-P Swirl Finder\u003c\/a\u003e for specific swirl detection uses the DWL 2500 as a supplement for complete quality control — Swirl Finder for spot analysis, DWL 2500 for overall evaluation of the paint result.\u003c\/p\u003e\n\u003ch3\u003eBuying the FLEX DWL 2500 12\/18 — who benefits from the full-spectrum light?\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003eFLEX DWL 2500 12\/18 Full-Spectrum Light\u003c\/strong\u003e is aimed at professional detailers who want to perform paint inspection at the highest level, at body shop workers who need color matching and paint finish inspection, and at enthusiasts who not only want to polish well but also want to be sure whether their result is truly perfect. It is not an everyday light — it is a precision instrument for anyone for whom the quality of the paint finish is important.\u003c\/p\u003e\n\u003cp\u003eThe device is supplied without a battery and charger. For those already in the FLEX 18V system — with one of the \u003ca href=\"\/es\/products\/flex-xfe21518ec-15mm-akku-exzenterpolierer-freilauf-150mm-18v\"\u003eFLEX 18V polishers\u003c\/a\u003e or the \u003ca href=\"\/es\/products\/flex-bw180ec-akku-geblaese-detailing-set\"\u003eBW 18.0-EC blower\u003c\/a\u003e — the \u003cstrong\u003eFLEX DWL 2500 Full-Spectrum Light\u003c\/strong\u003e is the logical extension that can already be operated with the existing battery. No additional purchase, no other charging system — just insert the next AP 18V battery pack and go.\u003c\/p\u003e\n\u003cp\u003eFor those not yet in the FLEX 18V system, starting with the \u003ca href=\"\/es\/products\/flex-pset22q-akku-set-18v\"\u003eP-Set 22 Q\u003c\/a\u003e with two batteries and a charger is recommended — this immediately provides the necessary battery supply for alternating operation and makes the DWL 2500 a completely self-sufficient solution for mobile detailing without a power connection.\u003c\/p\u003e\n\u003cp\u003eAs a complement to the \u003ca href=\"\/es\/products\/flex-wls70190-mobiles-leuchten-stativ\"\u003eWLS-70-190 mobile lighting tripod\u003c\/a\u003e, the \u003cstrong\u003eFLEX DWL 2500 Full-Spectrum Light\u003c\/strong\u003e transforms into a full-fledged, tripod-mounted inspection and work light that leaves the detailer's hands free. The tripod set is the recommended configuration for anyone who wants to use the light in a fixed position for longer periods — as a permanent work light source above the vehicle, as an inspection light for the final phase, or as a mobile lighting solution for on-site customer use.\u003c\/p\u003e","brand":"FLEX","offers":[{"title":"DWL 2500 12\/18 \"532325\" (Without battery \/ charger)","offer_id":57377624916303,"sku":"D1-FLEX-532325","price":206.89,"currency_code":"EUR","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0800\/3272\/7375\/files\/flex-dwl-2500-12-18-led-vollspektrum-leuchte-12-18v-dwl-2500-12-18-532325-532325.png?v=1775058647"},{"product_id":"flex-wls70190-mobiles-leuchten-stativ","title":"\"WLS-70-190\" trípode de iluminación móvil","description":"\u003ch2\u003eFLEX WLS-70-190 Mobile Light Stand — Height-Adjustable 0.70–1.90m for Hands-Free Inspection with the DWL 2500\u003c\/h2\u003e\n\u003cblockquote\u003e\n\u003cp\u003e\u003cem\u003eWhat is the FLEX WLS-70-190? The WLS-70-190 is a mobile rolling stand made of powder-coated steel with a height-adjustable working range of 0.70 to 1.90m — designed as a fixed mounting bracket for the FLEX DWL 2500 full-spectrum light and other FLEX work lights for professional detailing and workshop use.\u003c\/em\u003e\u003c\/p\u003e\n\u003c\/blockquote\u003e\n\u003chr\u003e\n\u003cp\u003eAnyone who seriously wants to use the \u003ca href=\"\/es\/products\/flex-dwl250012-18-vollspektrum-leuchte\"\u003eFLEX DWL 2500 full-spectrum light\u003c\/a\u003e will eventually need both hands free. Light in one hand, polisher in the other — that doesn't work. The \u003cstrong\u003eFLEX WLS-70-190 Light Stand\u003c\/strong\u003e is the answer: a stable, wheeled stand that positions the DWL 2500 at exactly the right height and fixes it there, while the detailer works unhindered. The \u003cstrong\u003eFLEX WLS-70-190\u003c\/strong\u003e is thus more than an accessory — it is the prerequisite for the DWL 2500 to unfold its full potential as an inspection light.\u003c\/p\u003e\n\u003cp\u003eThe WLS-70-190 is not a generic camera tripod with an adapter plate — it is a dedicated mounting bracket from the FLEX accessory system, tailored to the requirements of professional workshop lighting. Powder-coated steel, five castors for quick repositioning on the vehicle, two of them with locking function for a secure stand during inspection — everything about this stand is designed for everyday workshop use, not for occasional leisure use.\u003c\/p\u003e\n\u003cp\u003eThe working range of 0.70 to 1.90m covers all relevant working heights: from sill polishing at ground level to roof inspection of an SUV. The \u003cstrong\u003eFLEX WLS-70-190 Light Stand\u003c\/strong\u003e can be adjusted in height without tools and moved from one side of the vehicle to the other in seconds. For detailers who work on several vehicles daily, this is a significant time saving compared to constantly holding and repositioning the light by hand.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e0.70–1.90m Height Adjustment — full coverage from sill to car roof.\u003c\/strong\u003e The working stroke of the WLS-70-190 covers the entire body height of a car: 0.70m for sills, wheel arches and lower parts, 1.90m for the hood and roof of an SUV. The height adjustment is stepless via a clamp lock and can be operated with one hand. Once set to the desired working height, the stand remains stable in position — no readjustment, no correction.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFive castors, two with locking function — mobile and secure at the same time.\u003c\/strong\u003e The five castors make the WLS-70-190 a true workshop solution: roll the light along the vehicle without lifting or dragging the stand. The two lockable castors secure the stand in the inspection position — no unwanted rolling away, no wobbling during the grazing light check. This saves time and keeps the light stable in the selected inspection position.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePowder-coated steel for durable workshop use.\u003c\/strong\u003e The stand frame made of powder-coated steel is robust enough for daily professional operation. A dead weight of 6.15 kg gives the WLS-70-190 the necessary stability even on smooth workshop floors when the light is positioned at full height. The weight is very low for a stand of this size and load capacity and makes transport in the transporter or tool trolley easy.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003chr\u003e\n\u003cblockquote class=\"praxistipp\"\u003e\n\u003cp\u003e\u003cstrong\u003ePractical tip from Detailing1:\u003c\/strong\u003e For efficient paint inspection after polishing, we recommend setting the WLS-70-190 to the height of the vehicle's center and rolling it along the vehicle from front to back — instead of holding the light by hand. In the grazing light check (DWL 2500 at 6,500K), you simply roll along the flank at a distance of 30–45cm. Both hands free, constant distance, consistent angle: you see more, faster and more reliably than with the light in your hand.\u003c\/p\u003e\n\u003c\/blockquote\u003e\n\u003chr\u003e\n\u003ch3\u003eConstruction and Materials of the WLS-70-190 — Steel, Castors and Stability for Everyday Workshop Use\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003eFLEX WLS-70-190 Light Stand\u003c\/strong\u003e is made of powder-coated steel — a material that has proven itself in toolmaking for decades and combines impact resistance, corrosion protection and durability. The powder coating protects against rust from polishing dust, water sprayers and cleaning agent splashes, which are unavoidable in detailing. Not painted steel that immediately rusts when scratched — the powder coating is significantly more robust and designed for continuous industrial use.\u003c\/p\u003e\n\u003cp\u003eThe dead weight of 6.15 kg is remarkably low for a stand of this height and construction class. At the same time, it ensures sufficient stability on smooth ground when the light is positioned at a full height of 1.90m — the center of gravity remains low enough due to the wide castor base to prevent tipping, even when the DWL 2500 is mounted with an 18V battery inserted. Compared to other workshop stands of this height, the WLS-70-190 is therefore a light and easy-to-handle tool.\u003c\/p\u003e\n\u003cp\u003eThe five castors are designed for workshop use: large enough for smooth screed floors and epoxy surfaces, compact enough to maneuver the stand even in confined workshop situations. The two lockable castors are located at the front base and can be fixed with a foot pedal — no bending, no tools necessary. In practice, this means: roll in, lock, check, release, continue. A cycle that repeats itself dozens of times in every inspection round, thus running completely automatically.\u003c\/p\u003e\n\u003cp\u003eThe clamp lock for height adjustment is designed for one-handed operation. In the typical detailing workflow, where the height is changed multiple times per vehicle — deep sills, door center, roof edge — this is a real comfort gain compared to stands that require a two-handed clamping screw. Anyone who has worked with such a stand and then switches to the WLS-70-190 will immediately notice the difference: everything goes faster, with less effort, without interrupting the work rhythm.\u003c\/p\u003e\n\u003ch3\u003eWorking Heights and Workflow — the WLS-70-190 in Everyday Detailing\u003c\/h3\u003e\n\u003cp\u003eThe working stroke of 0.70 to 1.90m was not chosen by chance. It corresponds to the real requirements of vehicle preparation: the lower limit of 0.70m allows the illumination of sills, entry areas and low side parts at ground level — areas that are often neglected in paint inspection, but regularly show the most contact marks. The upper limit of 1.90m is sufficient for the hood and roof of most SUV classes up to the upper edge of a city van.\u003c\/p\u003e\n\u003cp\u003eIn the practical workflow, this looks like this: set the stand to shoulder height (approx. 1.40m) for the side panels, then raise it to 1.70m for the hood and lower it to 0.80m for the sills. Each adjustment takes less than 5 seconds with the one-hand clamping. A complete inspection tour of the vehicle is completed in 10–15 minutes — with the light in hand, the same check would take significantly longer and would be less reproducible. The time saving in daily operation quickly adds up: for three vehicles daily, 30–40 minutes can be saved, which would otherwise be spent on manual holding and repositioning.\u003c\/p\u003e\n\u003cp\u003eA special advantage of the WLS-70-190 is the ability to leave the light in a fixed position while inspecting the vehicle around the stand — instead of guiding the stand around the vehicle. For large-area inspection tasks, such as roof inspection or a complete hood check, the stand is optimally positioned once and you turn yourself, not the stand. This provides a more consistent assessment perspective.\u003c\/p\u003e\n\u003cp\u003eFor mobile detailers who work on-site at customers' premises, the WLS-70-190 can be easily stowed in the transporter. The construction is compact enough for a standard tool trolley or the loading area of a small transporter. The stand is not designed for collapsible portability like a travel tripod, but for daily transport between jobs — and robust enough to withstand this daily use for years.\u003c\/p\u003e\n\u003ch3\u003eWLS-70-190 and DWL 2500 — the Recommended Combination Setup\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003eFLEX WLS-70-190 Light Stand\u003c\/strong\u003e is mechanically matched to the \u003ca href=\"\/es\/products\/flex-dwl250012-18-vollspektrum-leuchte\"\u003eDWL 2500 12\/18 Full-Spectrum Light\u003c\/a\u003e. The stand's mounting bracket directly and securely accommodates the DWL 2500 — no adapter, no improvised connection. The stand was developed together with the light and is the only FLEX-recommended support system for the DWL 2500 in stationary operation.\u003c\/p\u003e\n\u003cp\u003eIn the combination setup, the DWL 2500 provides the light quality (CRI RA 96, 2,500–6,500K, 3,000 lumens), the WLS-70-190 the positioning. Both parts solve a problem that neither can solve alone: the DWL 2500 without a stand is a precise hand tool that occupies one hand; the DWL 2500 on the WLS-70-190 is a fully automatically positioned inspection light that leaves both hands of the detailer free.\u003c\/p\u003e\n\u003cp\u003eFor workshops employing several detailers, it is recommended to purchase two WLS-70-190 stands — one for the left side of the vehicle, one for the right. With two DWL 2500s and two stands, a vehicle can be completely illuminated in a single pass inspection, without swinging and without loss of time.\u003c\/p\u003e\n\u003ch3\u003eWLS-70-190 in Comparison — Rolling Stand vs. Floor Stand and Wall Mount\u003c\/h3\u003e\n\u003cp\u003eIn everyday workshop life, there are various approaches to positioning work lights: wall-mounted swivel arms, simple floor stands without castors, and mobile rolling stands like the WLS-70-190. Which solution is right depends on the working environment.\u003c\/p\u003e\n\u003cp\u003eWall-mounted swivel arms are the most convenient solution for fixed inspection stations — but they require a fixed parking space, a wall at the right distance and an installation. For mobile detailers who work at the customer's premises, this option is not available. For workshops with changing vehicle sizes and flexible parking spaces, the fixed wall mount is often not as practical as it seems.\u003c\/p\u003e\n\u003cp\u003eSimple floor stands without castors are inexpensive, but impractical in everyday use: every repositioning requires lifting and carrying, which becomes cumbersome with a stand of this load class. The \u003cstrong\u003eFLEX WLS-70-190\u003c\/strong\u003e with its five castors solves this problem completely — the stand is simply rolled, not carried.\u003c\/p\u003e\n\u003cp\u003eThe rolling stand is therefore the superior solution for anyone who needs flexibility in use and no fixed infrastructure. For professional detailers who use the DWL 2500 intensively, the WLS-70-190 is the natural complement — not a compromise, but the support system developed for it.\u003c\/p\u003e\n\u003ch3\u003eBuying the FLEX WLS-70-190 — Who Benefits from the Light Stand?\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003eFLEX WLS-70-190 Mobile Light Stand\u003c\/strong\u003e is the right choice for anyone who uses the \u003ca href=\"\/es\/products\/flex-dwl250012-18-vollspektrum-leuchte\"\u003eDWL 2500 Full-Spectrum Light\u003c\/a\u003e professionally and wants both hands free. It is not a mandatory component for every beginner — anyone who occasionally uses the DWL 2500 by hand can manage without a stand. However, anyone who uses it daily for paint inspection, quality assurance and acceptance inspections will quickly consider the WLS-70-190 indispensable.\u003c\/p\u003e\n\u003cp\u003eEspecially for professional detailers and body shops that work on several vehicles daily, the stand pays for itself through pure time savings. No holding, no manual repositioning, no tired shoulder after the third vehicle — the stand takes over the positioning work, the detailer the judgment work. The result is a more reproducible, faster and less tiring quality control.\u003c\/p\u003e\n\u003cp\u003eThose planning a purchase are advised to plan for the bundle of \u003ca href=\"\/es\/products\/flex-dwl250012-18-vollspektrum-leuchte\"\u003eDWL 2500\u003c\/a\u003e and WLS-70-190 together. The light alone is already a high-quality tool; together with the stand, it becomes a complete, stand-supported inspection solution that meets all requirements of professional paint inspection — from the first hologram check after polishing to the final acceptance inspection before vehicle handover.\u003c\/p\u003e","brand":"FLEX","offers":[{"title":"WLS-70-190 \"511064\"","offer_id":57377625145679,"sku":"D1-FLEX-511064","price":171.36,"currency_code":"EUR","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0800\/3272\/7375\/files\/flex-wls-70-190-mobiles-leuchten-stativ-wls-70-190-511064-511064.png?v=1775059325"},{"product_id":"flex-mwl1504-mehrzweck-stirnlampe","title":"\"MWL 150 4\" Linterna Frontal Multiusos","description":"\u003ch2\u003eFLEX MWL 150 4 Multi-Purpose Headlamp — CRI 97, 2,500–6,500K Color Temperature, and PXE Clip for PXE 80 Polisher\u003c\/h2\u003e\n\u003cblockquote\u003e\n\u003cp\u003e\u003cem\u003eWhat is the FLEX MWL 150 4 Multi-Purpose Headlamp? The FLEX MWL 150 4 is a compact 4V LED headlamp with CRI 97 and stepless color temperature from 2,500K to 6,500K — equipped with a PXE clip for direct mounting on the FLEX PXE 80 polisher, as well as a headband, cap clip, and integrated magnet for versatile use in detailing.\u003c\/em\u003e\u003c\/p\u003e\n\u003c\/blockquote\u003e\n\u003chr\u003e\n\u003cp\u003eA headlamp in detailing initially sounds like a fringe topic. Until you use the \u003ca href=\"\/es\/products\/flex-pxe8012ec-akku-exzenterpolierer-80mm-12v\"\u003ePXE 80 polisher\u003c\/a\u003e for the first time in tight vehicle areas and realize that the light simply isn't enough — because your upper body is hanging over the surface and the overhead light is at exactly the wrong angle. The \u003cstrong\u003eFLEX MWL 150 4 Multi-Purpose Headlamp\u003c\/strong\u003e elegantly solves this problem: it attaches directly to the PXE 80 via a PXE clip and illuminates the work surface from the optimal angle — continuously, without occupying a hand.\u003c\/p\u003e\n\u003cp\u003eWith CRI 97 and color temperature adjustment from 2,500K to 6,500K, the \u003cstrong\u003eFLEX MWL 150 4\u003c\/strong\u003e goes far beyond what normal headlamps can do. It's not just a work light for dark corners — it's a precise control instrument that delivers the same color accuracy as professional photo studio lights. For detailing work in vehicle interiors, engine compartments, and tight body parts, this is the crucial difference between a work light and a control tool.\u003c\/p\u003e\n\u003cp\u003eThe multi-purpose function of the \u003cstrong\u003eFLEX MWL 150 4 Multi-Purpose Headlamp\u003c\/strong\u003e makes it the most versatile light in the FLEX portfolio: headband for hands-free work, cap clip for comfortable wearing during longer work phases, PXE clip for mounting on the polisher, and an integrated magnet for temporary attachment to metal parts. Four attachment options, one device — that's an approach that proves its worth in practice.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCRI 97 and 2,500–6,500K — ultimate color rendering in your pocket.\u003c\/strong\u003e With a Color Rendering Index of 97, the MWL 150 4 even surpasses many professional workshop lights. In combination with the stepless color temperature adjustment from warm white (2,500K) to daylight (6,500K), it is the most compact CRI 97 light in the FLEX portfolio. For checking paint subtleties in tight areas — door edges, spoiler undersides, sill areas — this color accuracy is just as crucial as with the large DWL 2500.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePXE clip for direct mounting on the PXE 80 — illuminating the work surface during polishing.\u003c\/strong\u003e The included PXE clip allows the MWL 150 4 to be attached directly to the FLEX PXE 80. The result: the lamp automatically illuminates the current work surface — regardless of the machine's position and without any manual effort. Especially in dark vehicle corners, door cutouts, and under bumpers, this is a significant relief that cannot be achieved as easily with any other lighting solution.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e54g weight, USB-C charging, and integrated magnet — maximum flexibility.\u003c\/strong\u003e At 54g, the MWL 150 4 is so light that it won't be a burden even after hours of wearing it with the headband. USB-C charging allows it to be charged with any modern power supply, laptop, or mobile battery — no proprietary chargers, no additional weight in the toolbox. The integrated magnet allows temporary attachment to metal parts in the vehicle or to workshop equipment — practical for short inspection breaks.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003chr\u003e\n\u003cblockquote class=\"praxistipp\"\u003e\n\u003cp\u003e\u003cstrong\u003eDetailing1 Pro Tip:\u003c\/strong\u003e For interior polishing and tight body areas with the PXE 80, we recommend attaching the MWL 150 4 directly to the polisher via the PXE clip and setting it to 6,500K. The light automatically follows the machine's position and illuminates precisely the area you're working on. After polishing, switch to the headband and use it for the swirl mark check — the same light, two modes of use, zero changeover time.\u003c\/p\u003e\n\u003c\/blockquote\u003e\n\u003chr\u003e\n\u003ch3\u003eCRI 97 in Compact Size — Why Color Rendering Is Crucial Even for Small Lights\u003c\/h3\u003e\n\u003cp\u003eThe CRI 97 value of the \u003cstrong\u003eFLEX MWL 150 4 Multi-Purpose Headlamp\u003c\/strong\u003e is surprising at first glance for a device of this size. In practice, however, it is the most important reason to buy for detailers who are familiar with the CRI demands of the large DWL 2500 and want to maintain this standard for compact work.\u003c\/p\u003e\n\u003cp\u003eWhat CRI 97 means in practice: color tone deviations between body parts after refinishing are recognizable even under this small lamp. Fine holograms in door edges or sill areas — areas that are difficult to reach with large tripods — become visible with the MWL 150 4 in grazing light mode. The combination of high CRI and variable color temperature makes the lamp a full-fledged control tool, not just a work light.\u003c\/p\u003e\n\u003cp\u003eThe comparison with commercially available headlamps is sobering: most cheap headlamps with CRI 70–80 show paint tones slightly distorted and make fine defects invisible. In an area where the result depends on the quality of lighting, this difference is directly relevant to the quality of the work.\u003c\/p\u003e\n\u003cp\u003eThe stepless color temperature adjustment from 2,500K to 6,500K significantly expands the application possibilities. Warm white light for evaluating warm paint colors, neutral light for general work, cool daylight for the final defect check — these functions are fully available even in the small compact lamp.\u003c\/p\u003e\n\u003ch3\u003ePXE Clip and Four Mounting Modes — The Versatility of the MWL 150 4\u003c\/h3\u003e\n\u003cp\u003eThe included \u003cstrong\u003ePXE clip\u003c\/strong\u003e is the most striking feature of the FLEX MWL 150 4 compared to other headlamps. It allows secure attachment directly to the \u003ca href=\"\/es\/products\/flex-pxe8012ec-akku-exzenterpolierer-80mm-12v\"\u003eFLEX PXE 80 polisher\u003c\/a\u003e — without tape, without improvisation, without restricting machine handling.\u003c\/p\u003e\n\u003cp\u003eIn PXE clip mode, the lamp becomes an integrated work light for the polisher: it always illuminates the current work area, follows the machine, and provides a clear view of the pad and paint — even in areas where the workshop light is insufficient. For detailers who regularly polish in tight vehicle areas — door frames, bumper sections, roof edges — this is a tangible gain in quality and comfort.\u003c\/p\u003e\n\u003cp\u003eThe other three mounting modes expand the application possibilities: the headband turns the MWL 150 4 into a classic headlamp for maintenance work in the engine compartment or for interior inspections in dark vehicle interiors. The cap clip is the more comfortable option for longer work phases without headband pressure. The integrated magnet is suitable for temporary attachment to body parts or tools — for example, when parking the lamp for short work breaks.\u003c\/p\u003e\n\u003cp\u003eThe weight of 54g makes all four modes comfortable: the lamp is barely noticeable, no matter how it is worn. For a 4V LED lamp with CRI 97, variable color temperature, and four attachment options, this is an exceptional packaging density.\u003c\/p\u003e\n\u003ch3\u003eTechnical Features of the MWL 150 4 — 4V Battery, USB-C, and 54g Compact Housing\u003c\/h3\u003e\n\u003cp\u003eThe internal 4V lithium-ion battery of the \u003cstrong\u003eFLEX MWL 150 4\u003c\/strong\u003e can be charged via USB-C, fitting into any modern charging infrastructure. This means: no proprietary charger, no additional adapter, no expensive replacement batteries. If you have USB-C power supplies, power banks, or USB hubs in your workshop, you can charge the MWL 150 4 directly there — a daily convenience that you only appreciate after years of working with proprietary chargers.\u003c\/p\u003e\n\u003cp\u003eThe IP20 protection class is sufficient for indoor and workshop use — the lamp is protected against dust ingress, but not designed for wet work or direct water spray contact. For use on vehicles under normal detailing conditions, i.e., no direct spraying, IP20 is completely acceptable. For outdoor use in rain or during vehicle cleaning, the IP67-protected \u003ca href=\"\/es\/products\/flex-dwl250012-18-vollspektrum-leuchte\"\u003eDWL 2500\u003c\/a\u003e is recommended.\u003c\/p\u003e\n\u003cp\u003eThe weight of 54g is an important selling point. For a headlamp that is worn for hours, weight is the most important comfort factor — and 54g is far more comfortable than the 150–250g that many professional headlamps weigh. Even when mounted on the PXE clip, where the weight affects machine handling, 54g is barely noticeable.\u003c\/p\u003e\n\u003cp\u003eThe two brightness levels (75 lm and 150 lm) cover different application scenarios: 75 lm for continuous operation during polishing, 150 lm for the grazing light inspection check. The compact dimensions of 95 × 27 × 27mm fit into any toolbox and take up hardly any space during transport. The lamp is therefore an everyday companion that is always with you — not the heavy special tool that you only get out when needed.\u003c\/p\u003e\n\u003ch3\u003eMWL 150 4 in Comparison — Compact Headlamp vs. Dedicated Workshop Lights\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003eFLEX MWL 150 4\u003c\/strong\u003e is not designed as a replacement for the \u003ca href=\"\/es\/products\/flex-dwl250012-18-vollspektrum-leuchte\"\u003eDWL 2500\u003c\/a\u003e — it is a supplement for tasks where the DWL 2500 is too large and bulky. The comparison between the two lights is therefore not an either\/or, but a both\/and.\u003c\/p\u003e\n\u003cp\u003eThe DWL 2500 delivers 3,000 lumens over a large area and is suitable for overall vehicle inspection from a tripod. The MWL 150 4 delivers 150 lumens to a precise, small area and is suitable for close-up work, tight areas, and PXE 80 operation. Those who have both lights have a complete lighting solution for all phases of vehicle detailing — from large-area rough inspection to detailed spot control in body seams and door edges.\u003c\/p\u003e\n\u003cp\u003eCompared to generic headlamps from electronics retailers, the MWL 150 4 is clearly superior in two respects: CRI 97 instead of CRI 70–80 and the PXE clip function. The latter is unique in the market — no other headlamp is specifically designed for mounting on the FLEX PXE 80. For detailers who use the PXE 80 daily, this is a unique functional selling point without competition.\u003c\/p\u003e\n\u003ch3\u003eBuying the FLEX MWL 150 4 — Who Benefits from the Multi-Purpose Headlamp?\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003eFLEX MWL 150 4 Multi-Purpose Headlamp\u003c\/strong\u003e is recommended for all PXE 80 users who regularly polish in poor lighting conditions. As a dedicated accessory for the PXE 80, it belongs to the polisher's natural expansion set — alongside the DT adapter and the BP-M PXE hook-and-loop pad, the MWL 150 4 is the most practical addition for daily polishing work.\u003c\/p\u003e\n\u003cp\u003eFor all detailers who perform interior work, engine compartment inspections, or work in dark underbody areas, the MWL 150 4, as a freestanding headlamp with CRI 97, is a significant upgrade over cheaper alternatives. The light is accurate enough to reliably assess paint tones — even indoors without daylight.\u003c\/p\u003e\n\u003cp\u003eThe device comes with a USB-C cable and all four attachment accessories — headband, cap clip, PXE clip, and magnet. No separate battery needed, no charger — just connect it via USB-C to your existing charging infrastructure. For professional detailers and enthusiasts with a PXE 80, the \u003cstrong\u003eFLEX MWL 150 4 Multi-Purpose Headlamp\u003c\/strong\u003e is one of the most affordable ways to meaningfully expand your detailing setup's lighting arsenal — with the advantage that it serves not only as an accessory for the PXE 80 but also as a full-fledged inspection and work light for all other everyday workshop applications.\u003c\/p\u003e","brand":"FLEX","offers":[{"title":"MWL 150 4 \"534476\"","offer_id":57377625276751,"sku":"D1-FLEX-534476","price":89.89,"currency_code":"EUR","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0800\/3272\/7375\/files\/flex-mwl-150-4-mehrzweck-stirnlampe-mwl-150-4-534476-534476.png?v=1775059113"},{"product_id":"flex-tl4000-led-baustrahler-stativ-18v","title":"\"TL 4000 18.0\/230\" foco LED con trípode (18V)","description":"\u003ch2\u003eLED Work Light with Dual-Power — the FLEX TL 4000 18.0\/230 for Workshop and Detailing\u003c\/h2\u003e\n\u003cblockquote\u003e\n\u003cp\u003e\u003cem\u003eWhat is the FLEX TL 4000 18.0\/230? The FLEX TL 4000 18.0\/230 is a professional LED work light with a tripod — dual-power from an 18V battery or 230V mains, 4000 lumens in three stages, height-adjustable tripod from 1.1 to 2.2 meters for detailing, workshops, and mobile use.\u003c\/em\u003e\u003c\/p\u003e\n\u003c\/blockquote\u003e\n\u003chr\u003e\n\u003cp\u003eWork light that is truly sufficient — not just bright enough, but bright enough for the most demanding task in vehicle detailing: paint inspection. The \u003cstrong\u003eFLEX TL 4000 18.0\/230 LED work light\u003c\/strong\u003e delivers up to 4000 lumens of neutral white 4000 K light, making swirls, scratches, and paint defects visible that remain hidden under normal workshop lighting. The tripod positions the light precisely at working height — continuously adjustable from 1.1 to 2.2 meters — and the three-part lamp head can be swiveled on both axes until the light beam is exactly where it is needed.\u003c\/p\u003e\n\u003cp\u003eThe decisive feature of the TL 4000 18.0\/230 is its dual-power operation: the light runs either on a \u003ca href=\"\/es\/products\/flex-pset55r-akku-set-18v\"\u003eFLEX 18V battery pack\u003c\/a\u003e or directly from a 230V socket via a standard cold device cable. Those who work mobile — on-site with customers, at a vehicle event, or outdoors — use the battery and are independent of power outlets. Those who work in their own workshop simply plug in the power cord and save the battery for other devices. This flexibility is not a luxury in professional detailing, but a reality of work.\u003c\/p\u003e\n\u003cp\u003eThe FLEX TL 4000 18.0\/230 is aimed at detailers and reconditioners who perform professional paintwork under controlled lighting conditions: swirl inspection after polishing, quality control after ceramic sealing, paint correction in poorly lit workshops, mobile detailing assignments without a power outlet, and daily workshop operations where good work light prevents errors before they occur.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e4000 lumens in three stages — maximum brightness for professional paint inspection.\u003c\/strong\u003e The 4000-lumen stage of the TL 4000 delivers a light intensity that is rarely surpassed in detailing. For swirl inspection before and after paint correction, this amount of light is crucial: fine holograms and micro-scratches only become visible under sufficiently strong, targeted work light. The 1000 and 2000-lumen stages cover lighter tasks — general workshop lighting, interior work, and situations where battery capacity needs to be conserved.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDual-Power 18V + 230V — cordless mobile or permanently on mains, without changing devices.\u003c\/strong\u003e As the only light in the FLEX range, the TL 4000 combines the cordless freedom of the 18V battery system with the unlimited operating time of a mains connection. The standard cold device cable (sold separately) makes the light independent of the battery — at a fixed workshop station, mains operation is the more economical choice because the \u003ca href=\"\/es\/products\/flex-pset55r-akku-set-18v\"\u003eFLEX P-Set 55 R battery pack\u003c\/a\u003e remains reserved for the polishing machine.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHeight-adjustable tripod 1.1–2.2 m with three-part swivel head — precise light positioning.\u003c\/strong\u003e The integrated tripod optimally positions the light in every work situation: low for sill work and underbody inspection, high for the roof and hood. The three-part lamp head with two-axis swiveling allows precise alignment of the light beam to any body point. For gloss level control after polishing, this adjustability is more important than the raw lumen count — only with the correct angle of incidence do paint defects become visible.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003chr\u003e\n\u003cblockquote class=\"praxistipp\"\u003e\n\u003cp\u003e\u003cstrong\u003ePractical tip from Detailing1:\u003c\/strong\u003e Position the TL 4000 18.0\/230 at a medium height (approx. 1.5 m) and with a flat angle of incidence to the vehicle side — this is the most effective angle for swirl inspection. Grazing light makes holograms and polishing marks visible that remain hidden under direct light. After paint correction, set the light to 4000 lumens and systematically guide it over the body from back to front: only when the vehicle looks clean in this light is the polishing work truly complete. For mains operation, have a cold device cable (IEC C13) ready — this saves the battery for polisher and heat gun.\u003c\/p\u003e\n\u003c\/blockquote\u003e\n\u003chr\u003e\n\u003ch3\u003e4000 Lumens and 4000 K Neutral White — why light quality is crucial in detailing\u003c\/h3\u003e\n\u003cp\u003eNot every light shows paint defects equally well. The light temperature — measured in Kelvin — influences how well the human eye recognizes fine surface structures. The \u003cstrong\u003eFLEX TL 4000 18.0\/230\u003c\/strong\u003e operates at 4000 Kelvin, which is described as neutral white and is positioned between warm halogen yellow (2700–3000 K) and cool daylight (5500–6500 K). In practice, this means that the light produces a clear but not dazzlingly harsh light that reproduces paint colors naturally while sharpening contrasts for defect detection.\u003c\/p\u003e\n\u003cp\u003eThis compromise is ideal for paint correction: warm white light overpowers fine swirls because it creates hardly any contrasts. Cool white daylight is high-contrast but distorts paint colors and makes color assessment after sealing difficult. 4000 K hits the mark: clearly visible paint structure with color-accurate representation. For detailers who assess ceramic coatings by application — i.e., control the even curing film — neutral white is the right color temperature.\u003c\/p\u003e\n\u003cp\u003eThe three brightness levels of the TL 4000 (1000 \/ 2000 \/ 4000 lm) complement the high light quality with practical step control. For rough inspection or interior work, 1000 lm is sufficient without unnecessarily burdening the battery. 2000 lm is the all-round level for general workshop lighting. 4000 lm is used for critical paint inspection — when every detail counts and no defect can be overlooked. This gradation significantly extends battery life: operating the TL 4000 at 1000 lm provides significantly more time per charge cycle than at full load.\u003c\/p\u003e\n\u003cp\u003eFor comparison: commercially available workshop lights often operate with 800–1500 lm and warm white light. The TL 4000 delivers 2.5 to 5 times this performance at the highest level — with superior color temperature. For professional detailing results, this difference is measurable in the quality of the work delivered.\u003c\/p\u003e\n\u003ch3\u003eDual-Power in everyday work — 18V battery or 230V mains depending on the situation\u003c\/h3\u003e\n\u003cp\u003eThe dual-power capability of the \u003cstrong\u003eFLEX TL 4000 18.0\/230\u003c\/strong\u003e is more than a technical feature — it is a response to the practical reality of professional detailing. No detailer works exclusively in their own workshop, and no detailer always has a power outlet at hand. The TL 4000 is designed for both situations: cordless with the \u003ca href=\"\/es\/products\/flex-pset1888r-akku-set-xlithium-18v\"\u003eFLEX P-Set 18-88 R XLITHIUM battery pack\u003c\/a\u003e for maximum runtime without an outlet, or via cold device cable to the 230V mains for unlimited continuous operation in the workshop.\u003c\/p\u003e\n\u003cp\u003eIn battery operation, the runtime depends on the selected brightness level and the battery capacity used. With the \u003ca href=\"\/es\/products\/flex-pset55r-akku-set-18v\"\u003e5.0 Ah pack from the P-Set 55 R\u003c\/a\u003e and the medium brightness level (2000 lm), the TL 4000 easily achieves a runtime of 1–2 hours — sufficient for a complete vehicle inspection. For longer outdoor use, the 8.8 Ah pack from the P-Set 18-88 R is recommended, which extends the runtime accordingly. The advantage of the FLEX 18V system: every battery pack that runs on the polisher also runs in the TL 4000 — no separate battery system, no separate purchase costs.\u003c\/p\u003e\n\u003cp\u003eIn mains operation, any battery considerations are completely eliminated. A standard cold device cable (IEC C13 — the standard connection for computers and coffee machines, available in any electronics store) turns the TL 4000 into a stationary continuous light. For workshops with a fixed foiling or polishing station, mains operation is the most economical configuration: no battery charging effort, no runtime planning, no risk of interruption. The TL 4000 simply runs as long as the workshop is open.\u003c\/p\u003e\n\u003cp\u003eThe dual-power feature is particularly valuable for detailers who offer both: mobile assignments at the customer's site (with battery) and workshop work in their own business (with mains). Instead of buying two lights — one for mobile, one for the workshop — a single TL 4000 is sufficient for both applications. This reduces investment costs and significantly simplifies equipment organization.\u003c\/p\u003e\n\u003ch3\u003eTripod and lamp head — professional light positioning for bodywork and interior\u003c\/h3\u003e\n\u003cp\u003eA construction spotlight without an adjustable tripod is hardly usable for professional detailing — the correct light position makes the difference between a visible paint defect and an overlooked dent. The integrated tripod of the \u003cstrong\u003eFLEX TL 4000 18.0\/230\u003c\/strong\u003e is continuously adjustable from 1.1 to 2.2 meters. This range covers practically all relevant work situations: 1.1 meters for sill areas, door sills and lower doors, 1.6–1.8 meters for sides and hood, 2.2 meters for roof and high-mounted spoilers.\u003c\/p\u003e\n\u003cp\u003eThe lamp head itself consists of three individually swiveling panels on two axes. This means: the light can be used as a floodlight that illuminates a wide area evenly, or as a directed spotlight that is aimed precisely at a body point. For swirl inspection, flat, grazing light is the right technique — here, the panels are aligned parallel to the vehicle side, so that the light sweeps flat over the surface and makes scratches visible by creating shadows. For interior lighting, the panels are tilted inwards and focus the light on the passenger compartment.\u003c\/p\u003e\n\u003cp\u003eThe dimensions of the light (1190 × 295 × 275 mm assembled, weight 8.2 kg without battery) are appropriate for a professional work light of this class. The tripod can be folded for transport and storage, which makes mobile use practical. The weight of 8.2 kg is transportable, but not a device for frequent one-man quick transports — for mobile assignments to the customer, a stable transport case or carrying bag is recommended.\u003c\/p\u003e\n\u003cp\u003eThe \u003ca href=\"\/es\/products\/flex-wls70190-mobiles-leuchten-stativ\"\u003eFLEX WLS-70-190 Mobile Light Tripod\u003c\/a\u003e is an additional option for workshops that frequently need to reposition their TL 4000 — the separate tripod with wheels simplifies quick repositioning without complete reassembly. In combination with the TL 4000, the WLS-70-190 is the professional workshop solution for detailers who inspect multiple vehicle sides in one work step.\u003c\/p\u003e\n\u003ch3\u003eComparison TL 4000 vs. DWL 2500 and WL 1000 — which FLEX LED light for which purpose\u003c\/h3\u003e\n\u003cp\u003eThe FLEX lighting portfolio offers several options for detailing. In a direct \u003cstrong\u003ecomparison\u003c\/strong\u003e between the \u003cstrong\u003eFLEX TL 4000 18.0\/230\u003c\/strong\u003e, \u003ca href=\"\/es\/products\/flex-dwl25001218-led-vollspektrum-leuchte\"\u003eDWL 2500 12\/18 LED Full-Spectrum Light\u003c\/a\u003e, and \u003ca href=\"\/es\/products\/flex-wl100018-led-akku-strahler-18v\"\u003eWL 1000 18.0 LED Battery-Powered Spotlight\u003c\/a\u003e, clear differences emerge that depend on the specific application profile.\u003c\/p\u003e\n\u003cp\u003eThe TL 4000 18.0\/230 is the choice for area lighting and professional paint inspection on the entire vehicle. The 4000 lumens, the tripod, and the swivel three-panel lamp head make it the most powerful work solution when it comes to fully illuminating an entire vehicle. Dual-power operation and the tripod height of up to 2.2 m are unique selling points that none of the smaller lights offer.\u003c\/p\u003e\n\u003cp\u003eThe DWL 2500 12\/18 is a full-spectrum light for special applications: full-spectrum light (high CRI value) is particularly suitable for color assessment because it reproduces paint colors similarly to natural daylight. For paint professionals or detailers who assess color corrections, the DWL 2500 is the more precise choice. With 2500 lumens, it is brighter than the WL 1000, but weaker than the TL 4000 — and it has no tripod, which limits its direct use.\u003c\/p\u003e\n\u003cp\u003eThe WL 1000 18.0 is the compact, handy version for targeted spot lighting: individual body areas, interior inspections, and small work areas. With 1000 lumens and no tripod, it is the quickly deployable addition, not a main solution for complete vehicle inspection. In combination with the TL 4000 as the main light, the WL 1000 is ideal for targeted follow-up inspections of individual areas.\u003c\/p\u003e\n\u003cp\u003eFor a fully equipped detailing workshop, we recommend: TL 4000 as the main work light for paint inspection and area lighting, WL 1000 as a handy auxiliary light for targeted spot applications. This combination covers all relevant lighting tasks.\u003c\/p\u003e\n\u003ch3\u003eBuy FLEX TL 4000 18.0\/230 — the professional lighting system for demanding detailers\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003eFLEX TL 4000 18.0\/230 LED work light\u003c\/strong\u003e is the professional main light for detailers and reconditioners who accept no compromises in paint inspection. The combination of 4000 lumens in neutral white, the height-adjustable tripod, and the dual-power operation from battery and mains makes the TL 4000 the most versatile work light in the FLEX range — for the fixed workshop as well as for mobile use.\u003c\/p\u003e\n\u003cp\u003eThe device is available without battery and charger (SKU D1-FLEX-530375) — for all those who are already in the FLEX 18V system and use existing battery packs. Those new to the FLEX 18V system combine the TL 4000 with the \u003ca href=\"\/es\/products\/flex-pset55r-akku-set-18v\"\u003eP-Set 55 R battery set\u003c\/a\u003e for immediate use. The 5.0 Ah pack from the P-Set 55 R is the recommended main solution for work light operation: sufficient capacity for long work sessions during paint inspection, and reusable directly on the polisher after use on the work light.\u003c\/p\u003e\n\u003cp\u003eFor battery management, we recommend using the \u003ca href=\"\/es\/products\/flex-whp-wandhalter-haken\"\u003eFLEX WHP wall mount\u003c\/a\u003e: all battery packs of the 18V system are simultaneously charged and ready at the workshop wall — work light, polisher, and heat gun share the same battery pool. All packs charged in the morning, rotation between devices during the day without charging interruptions. This is the FLEX 18V system in its complete, efficient form.\u003c\/p\u003e\n\u003cp\u003eAnyone who delivers professional paintwork must also be able to recognize professional paint defects. The TL 4000 18.0\/230 is the tool that makes swirls, holograms, and inclusions visible — even those that remain hidden under normal workshop lighting. It is not an accessory, but an integral part of the professional detailing workstation.\u003c\/p\u003e","brand":"FLEX","offers":[{"title":"TL 4000 18.0\/230 \"530375\" (Battery\/charger not included)","offer_id":57377625375055,"sku":"D1-FLEX-530375","price":291.89,"currency_code":"EUR","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0800\/3272\/7375\/files\/flex-tl-4000-18-0-230-led-baustrahler-mit-stativ-18v-tl-4000-18-0-230-530375-530375.png?v=1775059239"}],"url":"https:\/\/detailing1.co\/es\/collections\/beleuchtung.oembed","provider":"Detailing1","version":"1.0","type":"link"}