{"title":"Beleuchtung","description":"\u003ch2 id=\"speakable-headline\"\u003eBeleuchtung\u003c\/h2\u003e\n\u003cp id=\"speakable-definition\"\u003e\u003cstrong\u003eBeleuchtung\u003c\/strong\u003e: Leuchten machen Arbeitsbereiche und feine Oberflächenspuren sichtbar. Hand- und Stirnlampen erreichen enge Stellen, Strahler beleuchten größere Bereiche und Kontrollleuchten zeigen feine Spuren.\u003c\/p\u003e\n\u003cp\u003eLichtverteilung, Position und Versorgung werden nach der Aufgabe gewählt, nicht nur nach der maximalen Helligkeit.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/fr\/collections\/lackkontrollleuchten\"\u003eLackkontrollleuchten\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/fr\/collections\/arbeitsleuchten\"\u003eArbeitsleuchten\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","products":[{"product_id":"flex-sf150p-swirl-finder","title":"\"SF 150-P\" Swirl Finder","description":"\u003ch2\u003eFLEX SF 150-P Swirl Finder — lampe d'inspection pro pour swirls, hologrammes et défauts de vernis\u003c\/h2\u003e\n\u003cblockquote\u003e\n\u003cp\u003e\u003cem\u003eC'est quoi le FLEX SF 150-P Swirl Finder ? Le FLEX SF 150-P est une lampe d'inspection professionnelle pensée pour le contrôle du vernis — une lampe spot au faisceau ciblé qui révèle les swirls, les hologrammes, les rayures et les défauts fins du vernis, avant et après le polissage.\u003c\/em\u003e\u003c\/p\u003e\n\u003c\/blockquote\u003e\n\u003chr\u003e\n\u003cp\u003eLe meilleur polissage ne sert à rien si tu ne peux pas le voir. Le \u003cstrong\u003eFLEX SF 150-P Swirl Finder\u003c\/strong\u003e est l'outil qui fait la différence entre un bon polissage et un polissage pro : une lampe d'inspection qui révèle les swirls, les hologrammes et les rayures fines sur le vernis, invisibles sous un éclairage normal. Polir sans swirl finder, c'est polir à l'aveugle.\u003c\/p\u003e\n\u003cp\u003eLe \u003cstrong\u003eFLEX SF 150-P\u003c\/strong\u003e n'est pas une lampe torche lambda — c'est un outil d'inspection dédié au travail du vernis, qui révèle la structure de surface grâce à un faisceau serré et ciblé sous un angle précis. Swirls et hologrammes, ce sont des rayures fines dans le vernis qui ressortent en motifs clairs sous une lumière rasante. Le SF 150-P pose exactement cette lumière rasante — sur une tache lumineuse bien définie, assez nette pour l'inspection de détail.\u003c\/p\u003e\n\u003cp\u003eEn tant qu'outil d'inspection, le SF 150-P complète tout le système de polissage FLEX : tu t'en sers avant de polir pour évaluer les défauts, pendant le process pour suivre l'avancée, et après chaque étape pour vérifier le résultat. Un protocole de polissage sans outil d'inspection, c'est de la supposition — avec le SF 150-P, ça devient un contrôle qualité mesurable.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFaisceau spot ciblé pour une visibilité précise des swirls et des hologrammes — l'œil du détailleur pro.\u003c\/strong\u003e Le SF 150-P projette une tache concentrée sous un angle d'incidence défini, qui fait ressortir les rayures fines et les swirls du vernis en motifs clairs. Ce faisceau spot, c'est la base technique de l'inspection pro du vernis : une lumière diffuse ne ferait pas ressortir ces structures fines — le spot serré les rend visibles sans ambiguïté, même pour un œil pas encore aguerri.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOutil d'inspection pro pour l'avant et l'après-polissage — contrôle qualité à un niveau pro.\u003c\/strong\u003e Le SF 150-P rend l'avancée du polissage mesurable : avant la première étape de cut, il montre le type et la profondeur des défauts. Après chaque étape, il te dit si elle a retiré les défauts à fond ou s'il faut encore repasser. Cette boucle de retour, c'est le cœur du polissage pro — sans elle, tu bosses au pif.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFormat compact et maniable pour le quotidien — toujours à portée de main pour un contrôle rapide.\u003c\/strong\u003e Le format compact du SF 150-P en fait le compagnon idéal au quotidien : à portée sur l'établi ou dans ton tablier à outils, vite en main pour un contrôle intermédiaire, vite reposé quand tu n'en as pas besoin. Pas de trépied encombrant, pas de montage pénible — tu le prends, tu l'utilises, c'est réglé.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003chr\u003e\n\u003cblockquote class=\"praxistipp\"\u003e\n\u003cp\u003e\u003cstrong\u003eCe qu'on voit en pratique :\u003c\/strong\u003e Pour tirer le meilleur du FLEX SF 150-P Swirl Finder : assombris la zone d'inspection ou bosse dans les coins à l'ombre — la lumière du jour qui arrive de côté concurrence le faisceau spot et écrase la visibilité des swirls. Garde la tache lumineuse sous un angle rasant de 30–45° par rapport au vernis et fais-la glisser lentement sur la surface à contrôler — swirls et hologrammes apparaissent en motifs clairs, circulaires ou en étoile. Après l'étape de finish, contrôle la surface avec le SF 150-P sous plusieurs angles : un bon résultat est nickel sous tous les angles, sans hologramme planqué à une incidence de lumière particulière.\u003c\/p\u003e\n\u003c\/blockquote\u003e\n\u003chr\u003e\n\u003ch3\u003ePourquoi l'inspection fait tout — rendre visibles swirls et hologrammes\u003c\/h3\u003e\n\u003cp\u003eLes swirls, ce sont des rayures fines et circulaires dans le vernis, causées par de mauvaises méthodes de lavage, une technique de polissage bancale ou un mauvais polish. Sous le soleil direct ou sous un faisceau ciblé comme celui du \u003cstrong\u003eFLEX SF 150-P Swirl Finder\u003c\/strong\u003e, tu les vois bien — sous un éclairage indirect normal, à peine. Ça explique pourquoi les clients sont contents d'un polissage sous éclairage normal, puis revoient les swirls au premier jour de soleil.\u003c\/p\u003e\n\u003cp\u003eLes hologrammes sont un autre type de défaut : ils viennent d'une mauvaise technique, d'un régime trop élevé ou d'une mauvaise combinaison pad-polish au polissage machine. Contrairement aux swirls, les hologrammes ne sont pas circulaires — ils forment un motif régulier, strié, qui suit le passage du pad. Sous le faisceau spot du SF 150-P, on les repère nettement, et ils doivent avoir totalement disparu avant l'étape de finish — sinon le résultat final ne fait pas pro, peu importe le boulot mis dans le polissage.\u003c\/p\u003e\n\u003cp\u003ePour un détailleur expérimenté, l'inspection au SF 150-P n'est pas la fin du contrôle qualité — c'est le début : ce que tu trouves dicte le protocole. Les swirls profonds réclament l'étape de cut avec le PP-C ; les hologrammes fins d'un passage précédent partent au PP-M ou au PP-F ; un film gras en surface n'est pas une rayure mais un souci de nettoyage, qui appelle autre chose. L'inspection au SF 150-P rend cette différence visible — et évite l'erreur la plus chère du detailing : le mauvais protocole pour le mauvais type de défaut.\u003c\/p\u003e\n\u003cp\u003ePour un débutant en detailing, le SF 150-P est un outil d'apprentissage : il montre ce qu'une bonne technique donne et ce qu'une mauvaise laisse derrière. Contrôle régulièrement au SF 150-P et juge le résultat après chaque étape, et tu apprendras plus sur la qualité de polissage en quelques sessions qu'à tâtonner sans outil de retour.\u003c\/p\u003e\n\u003ch3\u003eLe SF 150-P dans un workflow de polissage pro — l'inspection comme étape fixe\u003c\/h3\u003e\n\u003cp\u003eUn protocole de polissage pro avec le \u003cstrong\u003eFLEX SF 150-P Swirl Finder\u003c\/strong\u003e intégré ressemble à ça : voiture rentrée, nettoyage grossier, puis première inspection au SF 150-P — relevé systématique de tous les défauts du vernis, notes sur les zones à problème, protocole de polissage arrêté. Cette première inspection, c'est la base du devis que tu donnes au client et de ta propre organisation : combien d'étapes faut-il ? Quelles zones demandent plus de boulot ?\u003c\/p\u003e\n\u003cp\u003ePendant le polissage, le SF 150-P ressort après chaque étape : après l'étape de cut au \u003ca href=\"\/fr\/products\/flex-pp-c-cut-polierpad\"\u003ePP-C\u003c\/a\u003e, tu vérifies que toutes les rayures profondes ont sauté avant d'attaquer l'étape de compound. Après le compound au \u003ca href=\"\/fr\/products\/flex-pp-m-universal-polierpad\"\u003ePP-M\u003c\/a\u003e, tu vérifies que tous les hologrammes de l'étape de cut ont disparu. Ce n'est qu'une fois que le SF 150-P confirme qu'il ne reste plus d'hologrammes que tu lances l'étape de finish au \u003ca href=\"\/fr\/products\/flex-pp-f-finish-polierpad\"\u003ePP-F\u003c\/a\u003e.\u003c\/p\u003e\n\u003cp\u003eLe contrôle qualité final avant de rendre la voiture au client, c'est la dernière mission du SF 150-P : inspection systématique de chaque élément de carrosserie sous le faisceau spot — pas un hologramme, pas un swirl, pas un endroit oublié. Ce n'est qu'une fois cette inspection finale sans rien à signaler que la voiture est prête à être rendue. Dans ce workflow, le SF 150-P n'est pas optionnel : c'est le dernier verrou qualité avant la livraison.\u003c\/p\u003e\n\u003ch3\u003eÉquipement technique du SF 150-P — température de lumière, focus et autonomie\u003c\/h3\u003e\n\u003cp\u003eLa performance d'une lampe d'inspection ne tient pas qu'à la luminosité — les détails techniques du faisceau décident de la fiabilité avec laquelle les swirls ressortent. Le \u003cstrong\u003eFLEX SF 150-P\u003c\/strong\u003e embarque une température de couleur élevée, dans le blanc lumière du jour, proche du soleil naturel. C'est décisif : sous une lumière blanc chaud, beaucoup de swirls sont à peine visibles, parce que la température de couleur rougeâtre masque les reflets de lumière diffusée par les rayures. Le blanc lumière du jour avec un CRI élevé rend ces reflets nets et bien contrastés.\u003c\/p\u003e\n\u003cp\u003eLe spot ciblé du SF 150-P crée une limite nette entre la zone éclairée et la zone dans l'ombre. Cette limite nette compte pour l'inspection des swirls : hologrammes et swirls sont le plus visibles pile sur la ligne entre le spot clair et le fond sombre. Promène cette zone de transition systématiquement sur la surface et tu trouveras tous les défauts — même ceux qui ressortiraient moins au centre du spot.\u003c\/p\u003e\n\u003cp\u003ePour un usage prolongé, l'autonomie de la lampe est un vrai critère. Le SF 150-P est conçu pour un usage pro au quotidien — fabrication solide, assez de puissance lumineuse pour un tour complet de la voiture sans faiblir. Le format maniable permet de bosser sans se fatiguer, même sur des phases d'inspection plus longues.\u003c\/p\u003e\n\n\u003ch3\u003eLe SF 150-P face aux autres — lampe d'inspection dédiée vs. lampe torche et lumière du jour\u003c\/h3\u003e\n\u003cp\u003eLe SF 150-P n'est pas la seule lumière sous laquelle tu vois les swirls — mais c'est la plus efficace au quotidien. Mets-le face aux alternatives courantes et tu comprends pourquoi une lampe d'inspection dédiée est irremplaçable.\u003c\/p\u003e\n\u003cp\u003eLa lumière du jour montre bien les swirls — mais seulement sous soleil direct, au bon angle. En intérieur, le soleil direct est rare, et dehors ça dépend de la météo, de l'heure et de l'orientation de la voiture. Faire dépendre ton jugement sur la qualité de polissage uniquement du soleil, ce n'est ni systématique ni reproductible.\u003c\/p\u003e\n\u003cp\u003eLes lampes torches ordinaires ne donnent pas une lumière rasante assez ciblée pour l'inspection des swirls. Source trop diffuse, mauvaise plage du spectre, pas d'angle défini — résultat : une image peu fiable qui montre les swirls une fois sur deux, selon la façon dont tu tiens la lampe. Le SF 150-P élimine ce hasard : toujours le même type de lumière, toujours le même angle, toujours des résultats reproductibles.\u003c\/p\u003e\n\u003cp\u003eLes lampes plein spectre comme la \u003ca href=\"\/fr\/products\/flex-dwl-2500-vollspektrum-leuchte\"\u003eFLEX DWL 2500 lampe plein spectre\u003c\/a\u003e sont d'excellents éclairages d'ambiance pour tout l'espace, mais ne remplacent pas une lampe d'inspection à main. Le plafonnier plein spectre montre les swirls sur toute la surface — le SF 150-P les montre en détail à l'endroit précis que tu contrôles. Les deux outils se complètent : lumière plein spectre pour l'impression d'ensemble, SF 150-P pour le contrôle de détail ciblé. Qui a les deux a le contrôle qualité complet.\u003c\/p\u003e\n\u003ch3\u003eAcheter le FLEX SF 150-P — l'investissement qui améliore chaque polissage\u003c\/h3\u003e\n\u003cp\u003eÀ 47,48 €, le Swirl Finder est l'un des achats les moins chers de la caisse à outils d'un détailleur pro — et en même temps l'un des plus efficaces. Aucun pad hors de prix, aucune upgrade machine compliquée n'améliore la qualité de polissage aussi directement que l'outil qui, justement, la rend visible.\u003c\/p\u003e\n\u003cp\u003ePour un détailleur pro, le SF 150-P n'est pas une option en plus, c'est de l'équipement obligatoire. Proposer des prestations de polissage sans lampe d'inspection, c'est t'exposer aux réclamations de clients qui repèrent les hologrammes au soleil — alors que ton propre contrôle n'avait rien signalé. Le SF 150-P, c'est ton assurance contre ça : les hologrammes, tu les trouves toi-même, pas le client sur le parking.\u003c\/p\u003e\n\u003cp\u003eDans le cadre d'un set de polissage FLEX complet, on recommande le SF 150-P à côté des pads \u003ca href=\"\/fr\/products\/flex-pp-c-cut-polierpad\"\u003ePP-C\u003c\/a\u003e, \u003ca href=\"\/fr\/products\/flex-pp-m-universal-polierpad\"\u003ePP-M\u003c\/a\u003e et \u003ca href=\"\/fr\/products\/flex-pp-f-finish-polierpad\"\u003ePP-F\u003c\/a\u003e, comme pièce indispensable du workflow d'assurance qualité. Combine ces quatre outils et tu as un système complet pour la correction de vernis pro, contrôle qualité intégré — de la première rayure jusqu'à une inspection finale nickel et vérifiée.\u003c\/p\u003e\n","brand":"FLEX","offers":[{"title":"SF 150-P \"463302\"","offer_id":57377617740111,"sku":"D1-FLEX-463302","price":39.89,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0800\/3272\/7375\/files\/flex-sf-150-p-swirl-finder-sf-150-p-463302-463302.png?v=1775059236"},{"product_id":"flex-dwl25001218-led-vollspektrum-leuchte","title":"\"DWL 2500 12\/18\" Lampe LED Spectre Complet (12\/18V)","description":"\u003ch2\u003eFLEX DWL 2500 12\/18 Full-Spectrum Light — 3000 Lumens, CRI RA 96 and All-Daylight for Professional Paint Inspection\u003c\/h2\u003e\n\u003cblockquote\u003e\n\u003cp\u003e\u003cem\u003eWhat is the FLEX DWL 2500 12\/18 Full-Spectrum Light? The FLEX DWL 2500 is a battery-powered LED full-spectrum light with 3,000 lumens, CRI RA 96, and stepless color temperature adjustment from 2,500K to 6,500K — designed for professional paint inspection, hologram detection, and color matching in detailing.\u003c\/em\u003e\u003c\/p\u003e\n\u003c\/blockquote\u003e\n\u003chr\u003e\n\u003cp\u003eTo detect scratches, holograms, and paint defects, you need the right light. Not just bright enough, but also color-accurate enough — because many defects are simply invisible under incorrect light. The \u003cstrong\u003eFLEX DWL 2500 Full-Spectrum Light\u003c\/strong\u003e has been developed precisely for this requirement: a professional inspection light that, with CRI RA 96 and up to 3,000 lumens of work light, makes even the finest surface flaws, polishing marks, and color deviations visible.\u003c\/p\u003e\n\u003cp\u003eThe light is part of the \u003ca href=\"\/fr\/products\/flex-ap18-akku-pack-18v\"\u003eFLEX 18V battery system\u003c\/a\u003e and can be operated with 12V and 18V battery packs — a single device that can be flexibly used in the detailing station, for mobile applications, and on the vehicle. Thanks to its IP67 protection class, it is also suitable for use during car washes, polishing work with a water spray bottle, or in humid environments. The integrated USB power bank function also charges smartphones and tablets — practical for long detailing sessions where the phone cannot run out of battery.\u003c\/p\u003e\n\u003cp\u003eWith up to 30 hours of runtime at 300 lumens (economy mode) or full power for intensive inspection phases: it covers both operating modes, making it the most versatile light in the FLEX detailing portfolio. The flexible light intensity control makes it equally suitable as a continuous work light for the entire workday or as a focused inspection light for quality control in the final step.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCRI RA 96 — Photo studio level color rendering for maximum defect detection.\u003c\/strong\u003e A Color Rendering Index of RA 96 means that the light renders colors 96% as accurately as natural sunlight. This is crucial for paint inspection: color deviations between body parts, subtle holograms after polishing, and oxidation-related dullness are only reliably detectable under high-quality full-spectrum lighting. Cheap workshop lights with CRI below 80 distort colors and make defects invisible that clearly stand out under the DWL 2500.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAll-Daylight 2,500K–6,500K in 5 stages — Color temperature for every application.\u003c\/strong\u003e The gradual color temperature adjustment allows the light to be precisely matched to the task: Warm white light (2,500K) for evaluating warm-tone paints and metallic colors, neutral white light (4,000K) for general inspection, cool white daylight (6,500K) for detecting holograms and fine polishing marks. What is invisible at 4,000K often clearly catches the eye at 6,500K — and vice versa. This flexibility saves time and increases detection reliability.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIP67 waterproof, USB power bank, and 30h runtime — robust everyday usability.\u003c\/strong\u003e The IP67 protection class makes the DWL 2500 splash-proof and dust-tight — it withstands polishing dust, water sprays, and normal handling in daily detailing. The integrated USB-A interface for the power bank function allows external devices to be charged directly via the light's battery. Up to 30 hours of runtime in economy mode means: For mobile use without access to power outlets, the DWL 2500 is ready for several working days without recharging.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003chr\u003e\n\u003cblockquote class=\"praxistipp\"\u003e\n\u003cp\u003e\u003cstrong\u003ePractical tip from Detailing1:\u003c\/strong\u003e For hologram detection after polishing, we recommend setting the DWL 2500 to 6,500K (daylight) and guiding the light flat at a 30–45° angle over the polished surface. Glancing light makes polishing marks and uneven application visible that remain invisible under direct light. Only when the surface is flawless under this test do you move on to the next step. For final color evaluation, 4,000K is recommended for a neutral reference.\u003c\/p\u003e\n\u003c\/blockquote\u003e\n\u003chr\u003e\n\u003ch3\u003eCRI RA 96 and Full Spectrum — why color rendering is crucial for paint inspection\u003c\/h3\u003e\n\u003cp\u003eThe Color Rendering Index (CRI) is the decisive parameter for professional inspection lights. It describes how accurately a light source reproduces colors compared to natural sunlight (CRI 100). The \u003cstrong\u003eFLEX DWL 2500 Full-Spectrum Light\u003c\/strong\u003e achieves RA 96 — a value that is practically indistinguishable from daylight and is considered a mark of professionalism in the color control industry.\u003c\/p\u003e\n\u003cp\u003eWhat RA 96 means in practice: color deviations between replaced and original body parts after a repair paint job are reliably recognizable under this light. Holograms — the circular pattern that appears when the polishing process has not been completed cleanly — clearly stand out under full-spectrum light, even if they remain invisible under conventional neon light. The finest application marks from finishing pads, oxidation-related dullness at certain angles, differences in clear coat thickness — all of this is recognizable under RA 96 CRI light, making it impossible to overlook poor workmanship.\u003c\/p\u003e\n\u003cp\u003eFor customers who have high-end vehicles detailed, this control reliability is a quality argument: anyone who has worked and inspected with the DWL 2500 can confidently say that the result meets professional standards. And any detailer who delivers without this control step risks receiving complaints that would have been recognizable in the workshop with the right light.\u003c\/p\u003e\n\u003cp\u003eIn practice, the following inspection routine is recommended: first check the polished surface at 6,500K with glancing light (30° angle) for holograms and polishing marks, then at 4,000K for paint uniformity and potential transition zones. Only when both inspections have passed is the result truly ready for acceptance. With the DWL 2500, this routine can be performed quickly and without changing location — simply change the color temperature level, adjust the angle, and you're done.\u003c\/p\u003e\n\u003ch3\u003eAll-Daylight: 2,500K to 6,500K Color Temperature in 5 Stages\u003c\/h3\u003e\n\u003cp\u003eThe All-Daylight function of the DWL 2500 allows the selection of five color temperature levels between 2,500K and 6,500K. This is far more than a technical gimmick — each level has a specific function in the detailing workflow.\u003c\/p\u003e\n\u003cp\u003eWarm white light around 2,500–3,000K is particularly suitable for evaluating warm color tones: bronze, copper, warm silver, certain burgundy and red paints. These tones change their character significantly under cool light and are most accurately judged under warm white illumination. Detailers who work on vehicles with exclusive special colors benefit from this flexibility and can ensure that the color evaluation takes place under nearly natural conditions — not distorted by the cool blue light of a standard workshop lamp.\u003c\/p\u003e\n\u003cp\u003eNeutral white light around 4,000K is the most versatile setting for general work: uniform illumination without color shift, good for the polishing process itself, for pad changes, and for intermediate checks after individual steps. It is also the recommended setting for client consultations at the vehicle — the light is pleasant for the eye and gives the paint and bodywork a realistic, natural appearance.\u003c\/p\u003e\n\u003cp\u003eCool white daylight around 6,000–6,500K is the sharpest instrument for final quality control. Polishing marks, holograms, swirl marks, and paint defects are most clearly visible under this light — the glancing light combined with high color temperature is the best way to declare a paint surface definitively \"finished.\" Anyone who integrates this control step into the acceptance process works with a safety net that cheap tools simply cannot offer.\u003c\/p\u003e\n\u003cp\u003eThe staged switching is deliberately limited to five values — not stepless, but in defined steps. This has a practical advantage: the user can reproducibly access a preferred setting without having to scroll through a spectrum. In everyday use, this means: once learned which level applies to which task — and the DWL 2500 always provides the same reference basis for evaluation.\u003c\/p\u003e\n\u003ch3\u003e3,000 Lumens, IP67, and USB Power Bank — the comprehensive technical features of the DWL 2500\u003c\/h3\u003e\n\u003cp\u003eThe technical equipment of the DWL 2500 is comprehensive and designed for professional continuous operation. The 3,000 lumens in 18V operation are comparable to a very bright office grid lighting panel — enough to create additional contrasts even in brightly lit workshops and make defects visible that disappear in ambient light.\u003c\/p\u003e\n\u003cp\u003eThe IP67 protection class — dust-tight and temporarily submersible up to 1m — makes the light resistant to all normal influences in the detailing workshop: polishing dust, water from spray bottles, sweat, occasional drops onto damp ground. This is not a given for high-performance LED lights in this price range and a clear signal for professional use.\u003c\/p\u003e\n\u003cp\u003eThe integrated USB-A interface for the power bank function is a useful secondary feature: smartphone battery empty during a long outdoor assignment? Simply connect it to the light and continue charging. For mobile detailers who work for several hours without access to power outlets, this is a practical safeguard for communication with customers and for customer service during detailing.\u003c\/p\u003e\n\u003cp\u003eThe light intensity control allows stepless adjustment from 300 to 3,000 lumens. When set to 1,000–1,500 lumens for continuous use as work lighting, a 5.0 Ah battery charge lasts for several hours. For short inspection phases at full power (3,000 lumens), the device consumes more but provides maximum illumination in the shortest possible time. The combination of long runtime and high peak performance makes the DWL 2500 a reliable partner for any duration of use.\u003c\/p\u003e\n\u003ch3\u003eDWL 2500 Comparison — Full-Spectrum Light vs. Conventional Workshop and Photo Area Lights\u003c\/h3\u003e\n\u003cp\u003eStandard workshop lights with CRI 70–80 are sufficient for general work. For professional paint inspection, color matching, and hologram detection, they are unsuitable. The difference is significant: under CRI-80 light, a painted vehicle often looks perfect, even though fine swirl marks are present. Under the \u003cstrong\u003eFLEX DWL 2500 Full-Spectrum Light\u003c\/strong\u003e with RA 96, the same defects clearly stand out — and not just under ideal conditions, but also in a normal workshop situation with ambient light, polishing dust, and variable lighting conditions.\u003c\/p\u003e\n\u003cp\u003eDaylight simulation lights from the photography sector with a fixed color temperature (usually 5,500K) are an alternative but have decisive disadvantages: no battery operation, no IP protection class, no all-daylight range, and generally significantly worse robustness for use in the workshop. They are optimized for photo studio use — not for everyday professional detailing, where the light may occasionally fall to the ground, come into contact with spray water, or run for hours in high-intensity operation.\u003c\/p\u003e\n\u003cp\u003eInexpensive LED spotlights with daylight tint (often advertised as \"daylight\") mislead with bright lumen numbers but often only deliver CRI 75–85. This is sufficient for general lighting, but not for defect detection. Anyone who has compared a polished surface under CRI 96 and directly under CRI 80 will immediately understand the difference: what appears flawless under 80 shows its true defects under 96.\u003c\/p\u003e\n\u003cp\u003eThe \u003cstrong\u003eFLEX DWL 2500 Full-Spectrum Light\u003c\/strong\u003e combines the best of both worlds: photo studio color accuracy in a robust, battery-powered tool housing from the FLEX system. Anyone who uses the \u003ca href=\"\/fr\/products\/flex-sf150p-swirl-finder\"\u003eFLEX SF 150-P Swirl Finder\u003c\/a\u003e for specific swirl detection uses the DWL 2500 as a supplement for complete quality control — Swirl Finder for spot analysis, DWL 2500 for overall evaluation of the paint result.\u003c\/p\u003e\n\u003ch3\u003eBuying the FLEX DWL 2500 12\/18 — who benefits from the full-spectrum light?\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003eFLEX DWL 2500 12\/18 Full-Spectrum Light\u003c\/strong\u003e is aimed at professional detailers who want to perform paint inspection at the highest level, at body shop workers who need color matching and paint finish inspection, and at enthusiasts who not only want to polish well but also want to be sure whether their result is truly perfect. It is not an everyday light — it is a precision instrument for anyone for whom the quality of the paint finish is important.\u003c\/p\u003e\n\u003cp\u003eThe device is supplied without a battery and charger. For those already in the FLEX 18V system — with one of the \u003ca href=\"\/fr\/products\/flex-xfe21518ec-15mm-akku-exzenterpolierer-freilauf-150mm-18v\"\u003eFLEX 18V polishers\u003c\/a\u003e or the \u003ca href=\"\/fr\/products\/flex-bw180ec-akku-geblaese-detailing-set\"\u003eBW 18.0-EC blower\u003c\/a\u003e — the \u003cstrong\u003eFLEX DWL 2500 Full-Spectrum Light\u003c\/strong\u003e is the logical extension that can already be operated with the existing battery. No additional purchase, no other charging system — just insert the next AP 18V battery pack and go.\u003c\/p\u003e\n\u003cp\u003eFor those not yet in the FLEX 18V system, starting with the \u003ca href=\"\/fr\/products\/flex-pset22q-akku-set-18v\"\u003eP-Set 22 Q\u003c\/a\u003e with two batteries and a charger is recommended — this immediately provides the necessary battery supply for alternating operation and makes the DWL 2500 a completely self-sufficient solution for mobile detailing without a power connection.\u003c\/p\u003e\n\u003cp\u003eAs a complement to the \u003ca href=\"\/fr\/products\/flex-wls70190-mobiles-leuchten-stativ\"\u003eWLS-70-190 mobile lighting tripod\u003c\/a\u003e, the \u003cstrong\u003eFLEX DWL 2500 Full-Spectrum Light\u003c\/strong\u003e transforms into a full-fledged, tripod-mounted inspection and work light that leaves the detailer's hands free. The tripod set is the recommended configuration for anyone who wants to use the light in a fixed position for longer periods — as a permanent work light source above the vehicle, as an inspection light for the final phase, or as a mobile lighting solution for on-site customer use.\u003c\/p\u003e","brand":"FLEX","offers":[{"title":"DWL 2500 12\/18 \"532325\" (Without battery \/ charger)","offer_id":57377624916303,"sku":"D1-FLEX-532325","price":206.89,"currency_code":"EUR","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0800\/3272\/7375\/files\/flex-dwl-2500-12-18-led-vollspektrum-leuchte-12-18v-dwl-2500-12-18-532325-532325.png?v=1775058647"},{"product_id":"flex-wls70190-mobiles-leuchten-stativ","title":"\"WLS-70-190\" trépied d'éclairage mobile","description":"\u003ch2\u003eFLEX WLS-70-190 Mobile Light Stand — Height-Adjustable 0.70–1.90m for Hands-Free Inspection with the DWL 2500\u003c\/h2\u003e\n\u003cblockquote\u003e\n\u003cp\u003e\u003cem\u003eWhat is the FLEX WLS-70-190? The WLS-70-190 is a mobile rolling stand made of powder-coated steel with a height-adjustable working range of 0.70 to 1.90m — designed as a fixed mounting bracket for the FLEX DWL 2500 full-spectrum light and other FLEX work lights for professional detailing and workshop use.\u003c\/em\u003e\u003c\/p\u003e\n\u003c\/blockquote\u003e\n\u003chr\u003e\n\u003cp\u003eAnyone who seriously wants to use the \u003ca href=\"\/fr\/products\/flex-dwl250012-18-vollspektrum-leuchte\"\u003eFLEX DWL 2500 full-spectrum light\u003c\/a\u003e will eventually need both hands free. Light in one hand, polisher in the other — that doesn't work. The \u003cstrong\u003eFLEX WLS-70-190 Light Stand\u003c\/strong\u003e is the answer: a stable, wheeled stand that positions the DWL 2500 at exactly the right height and fixes it there, while the detailer works unhindered. The \u003cstrong\u003eFLEX WLS-70-190\u003c\/strong\u003e is thus more than an accessory — it is the prerequisite for the DWL 2500 to unfold its full potential as an inspection light.\u003c\/p\u003e\n\u003cp\u003eThe WLS-70-190 is not a generic camera tripod with an adapter plate — it is a dedicated mounting bracket from the FLEX accessory system, tailored to the requirements of professional workshop lighting. Powder-coated steel, five castors for quick repositioning on the vehicle, two of them with locking function for a secure stand during inspection — everything about this stand is designed for everyday workshop use, not for occasional leisure use.\u003c\/p\u003e\n\u003cp\u003eThe working range of 0.70 to 1.90m covers all relevant working heights: from sill polishing at ground level to roof inspection of an SUV. The \u003cstrong\u003eFLEX WLS-70-190 Light Stand\u003c\/strong\u003e can be adjusted in height without tools and moved from one side of the vehicle to the other in seconds. For detailers who work on several vehicles daily, this is a significant time saving compared to constantly holding and repositioning the light by hand.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e0.70–1.90m Height Adjustment — full coverage from sill to car roof.\u003c\/strong\u003e The working stroke of the WLS-70-190 covers the entire body height of a car: 0.70m for sills, wheel arches and lower parts, 1.90m for the hood and roof of an SUV. The height adjustment is stepless via a clamp lock and can be operated with one hand. Once set to the desired working height, the stand remains stable in position — no readjustment, no correction.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFive castors, two with locking function — mobile and secure at the same time.\u003c\/strong\u003e The five castors make the WLS-70-190 a true workshop solution: roll the light along the vehicle without lifting or dragging the stand. The two lockable castors secure the stand in the inspection position — no unwanted rolling away, no wobbling during the grazing light check. This saves time and keeps the light stable in the selected inspection position.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePowder-coated steel for durable workshop use.\u003c\/strong\u003e The stand frame made of powder-coated steel is robust enough for daily professional operation. A dead weight of 6.15 kg gives the WLS-70-190 the necessary stability even on smooth workshop floors when the light is positioned at full height. The weight is very low for a stand of this size and load capacity and makes transport in the transporter or tool trolley easy.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003chr\u003e\n\u003cblockquote class=\"praxistipp\"\u003e\n\u003cp\u003e\u003cstrong\u003ePractical tip from Detailing1:\u003c\/strong\u003e For efficient paint inspection after polishing, we recommend setting the WLS-70-190 to the height of the vehicle's center and rolling it along the vehicle from front to back — instead of holding the light by hand. In the grazing light check (DWL 2500 at 6,500K), you simply roll along the flank at a distance of 30–45cm. Both hands free, constant distance, consistent angle: you see more, faster and more reliably than with the light in your hand.\u003c\/p\u003e\n\u003c\/blockquote\u003e\n\u003chr\u003e\n\u003ch3\u003eConstruction and Materials of the WLS-70-190 — Steel, Castors and Stability for Everyday Workshop Use\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003eFLEX WLS-70-190 Light Stand\u003c\/strong\u003e is made of powder-coated steel — a material that has proven itself in toolmaking for decades and combines impact resistance, corrosion protection and durability. The powder coating protects against rust from polishing dust, water sprayers and cleaning agent splashes, which are unavoidable in detailing. Not painted steel that immediately rusts when scratched — the powder coating is significantly more robust and designed for continuous industrial use.\u003c\/p\u003e\n\u003cp\u003eThe dead weight of 6.15 kg is remarkably low for a stand of this height and construction class. At the same time, it ensures sufficient stability on smooth ground when the light is positioned at a full height of 1.90m — the center of gravity remains low enough due to the wide castor base to prevent tipping, even when the DWL 2500 is mounted with an 18V battery inserted. Compared to other workshop stands of this height, the WLS-70-190 is therefore a light and easy-to-handle tool.\u003c\/p\u003e\n\u003cp\u003eThe five castors are designed for workshop use: large enough for smooth screed floors and epoxy surfaces, compact enough to maneuver the stand even in confined workshop situations. The two lockable castors are located at the front base and can be fixed with a foot pedal — no bending, no tools necessary. In practice, this means: roll in, lock, check, release, continue. A cycle that repeats itself dozens of times in every inspection round, thus running completely automatically.\u003c\/p\u003e\n\u003cp\u003eThe clamp lock for height adjustment is designed for one-handed operation. In the typical detailing workflow, where the height is changed multiple times per vehicle — deep sills, door center, roof edge — this is a real comfort gain compared to stands that require a two-handed clamping screw. Anyone who has worked with such a stand and then switches to the WLS-70-190 will immediately notice the difference: everything goes faster, with less effort, without interrupting the work rhythm.\u003c\/p\u003e\n\u003ch3\u003eWorking Heights and Workflow — the WLS-70-190 in Everyday Detailing\u003c\/h3\u003e\n\u003cp\u003eThe working stroke of 0.70 to 1.90m was not chosen by chance. It corresponds to the real requirements of vehicle preparation: the lower limit of 0.70m allows the illumination of sills, entry areas and low side parts at ground level — areas that are often neglected in paint inspection, but regularly show the most contact marks. The upper limit of 1.90m is sufficient for the hood and roof of most SUV classes up to the upper edge of a city van.\u003c\/p\u003e\n\u003cp\u003eIn the practical workflow, this looks like this: set the stand to shoulder height (approx. 1.40m) for the side panels, then raise it to 1.70m for the hood and lower it to 0.80m for the sills. Each adjustment takes less than 5 seconds with the one-hand clamping. A complete inspection tour of the vehicle is completed in 10–15 minutes — with the light in hand, the same check would take significantly longer and would be less reproducible. The time saving in daily operation quickly adds up: for three vehicles daily, 30–40 minutes can be saved, which would otherwise be spent on manual holding and repositioning.\u003c\/p\u003e\n\u003cp\u003eA special advantage of the WLS-70-190 is the ability to leave the light in a fixed position while inspecting the vehicle around the stand — instead of guiding the stand around the vehicle. For large-area inspection tasks, such as roof inspection or a complete hood check, the stand is optimally positioned once and you turn yourself, not the stand. This provides a more consistent assessment perspective.\u003c\/p\u003e\n\u003cp\u003eFor mobile detailers who work on-site at customers' premises, the WLS-70-190 can be easily stowed in the transporter. The construction is compact enough for a standard tool trolley or the loading area of a small transporter. The stand is not designed for collapsible portability like a travel tripod, but for daily transport between jobs — and robust enough to withstand this daily use for years.\u003c\/p\u003e\n\u003ch3\u003eWLS-70-190 and DWL 2500 — the Recommended Combination Setup\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003eFLEX WLS-70-190 Light Stand\u003c\/strong\u003e is mechanically matched to the \u003ca href=\"\/fr\/products\/flex-dwl250012-18-vollspektrum-leuchte\"\u003eDWL 2500 12\/18 Full-Spectrum Light\u003c\/a\u003e. The stand's mounting bracket directly and securely accommodates the DWL 2500 — no adapter, no improvised connection. The stand was developed together with the light and is the only FLEX-recommended support system for the DWL 2500 in stationary operation.\u003c\/p\u003e\n\u003cp\u003eIn the combination setup, the DWL 2500 provides the light quality (CRI RA 96, 2,500–6,500K, 3,000 lumens), the WLS-70-190 the positioning. Both parts solve a problem that neither can solve alone: the DWL 2500 without a stand is a precise hand tool that occupies one hand; the DWL 2500 on the WLS-70-190 is a fully automatically positioned inspection light that leaves both hands of the detailer free.\u003c\/p\u003e\n\u003cp\u003eFor workshops employing several detailers, it is recommended to purchase two WLS-70-190 stands — one for the left side of the vehicle, one for the right. With two DWL 2500s and two stands, a vehicle can be completely illuminated in a single pass inspection, without swinging and without loss of time.\u003c\/p\u003e\n\u003ch3\u003eWLS-70-190 in Comparison — Rolling Stand vs. Floor Stand and Wall Mount\u003c\/h3\u003e\n\u003cp\u003eIn everyday workshop life, there are various approaches to positioning work lights: wall-mounted swivel arms, simple floor stands without castors, and mobile rolling stands like the WLS-70-190. Which solution is right depends on the working environment.\u003c\/p\u003e\n\u003cp\u003eWall-mounted swivel arms are the most convenient solution for fixed inspection stations — but they require a fixed parking space, a wall at the right distance and an installation. For mobile detailers who work at the customer's premises, this option is not available. For workshops with changing vehicle sizes and flexible parking spaces, the fixed wall mount is often not as practical as it seems.\u003c\/p\u003e\n\u003cp\u003eSimple floor stands without castors are inexpensive, but impractical in everyday use: every repositioning requires lifting and carrying, which becomes cumbersome with a stand of this load class. The \u003cstrong\u003eFLEX WLS-70-190\u003c\/strong\u003e with its five castors solves this problem completely — the stand is simply rolled, not carried.\u003c\/p\u003e\n\u003cp\u003eThe rolling stand is therefore the superior solution for anyone who needs flexibility in use and no fixed infrastructure. For professional detailers who use the DWL 2500 intensively, the WLS-70-190 is the natural complement — not a compromise, but the support system developed for it.\u003c\/p\u003e\n\u003ch3\u003eBuying the FLEX WLS-70-190 — Who Benefits from the Light Stand?\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003eFLEX WLS-70-190 Mobile Light Stand\u003c\/strong\u003e is the right choice for anyone who uses the \u003ca href=\"\/fr\/products\/flex-dwl250012-18-vollspektrum-leuchte\"\u003eDWL 2500 Full-Spectrum Light\u003c\/a\u003e professionally and wants both hands free. It is not a mandatory component for every beginner — anyone who occasionally uses the DWL 2500 by hand can manage without a stand. However, anyone who uses it daily for paint inspection, quality assurance and acceptance inspections will quickly consider the WLS-70-190 indispensable.\u003c\/p\u003e\n\u003cp\u003eEspecially for professional detailers and body shops that work on several vehicles daily, the stand pays for itself through pure time savings. No holding, no manual repositioning, no tired shoulder after the third vehicle — the stand takes over the positioning work, the detailer the judgment work. The result is a more reproducible, faster and less tiring quality control.\u003c\/p\u003e\n\u003cp\u003eThose planning a purchase are advised to plan for the bundle of \u003ca href=\"\/fr\/products\/flex-dwl250012-18-vollspektrum-leuchte\"\u003eDWL 2500\u003c\/a\u003e and WLS-70-190 together. The light alone is already a high-quality tool; together with the stand, it becomes a complete, stand-supported inspection solution that meets all requirements of professional paint inspection — from the first hologram check after polishing to the final acceptance inspection before vehicle handover.\u003c\/p\u003e","brand":"FLEX","offers":[{"title":"WLS-70-190 \"511064\"","offer_id":57377625145679,"sku":"D1-FLEX-511064","price":171.36,"currency_code":"EUR","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0800\/3272\/7375\/files\/flex-wls-70-190-mobiles-leuchten-stativ-wls-70-190-511064-511064.png?v=1775059325"},{"product_id":"flex-mwl1504-mehrzweck-stirnlampe","title":"\"MWL 150 4\" Lampe Frontale Multi-Usage","description":"\u003ch2\u003eFLEX MWL 150 4 Multi-Purpose Headlamp — CRI 97, 2,500–6,500K Color Temperature, and PXE Clip for PXE 80 Polisher\u003c\/h2\u003e\n\u003cblockquote\u003e\n\u003cp\u003e\u003cem\u003eWhat is the FLEX MWL 150 4 Multi-Purpose Headlamp? The FLEX MWL 150 4 is a compact 4V LED headlamp with CRI 97 and stepless color temperature from 2,500K to 6,500K — equipped with a PXE clip for direct mounting on the FLEX PXE 80 polisher, as well as a headband, cap clip, and integrated magnet for versatile use in detailing.\u003c\/em\u003e\u003c\/p\u003e\n\u003c\/blockquote\u003e\n\u003chr\u003e\n\u003cp\u003eA headlamp in detailing initially sounds like a fringe topic. Until you use the \u003ca href=\"\/fr\/products\/flex-pxe8012ec-akku-exzenterpolierer-80mm-12v\"\u003ePXE 80 polisher\u003c\/a\u003e for the first time in tight vehicle areas and realize that the light simply isn't enough — because your upper body is hanging over the surface and the overhead light is at exactly the wrong angle. The \u003cstrong\u003eFLEX MWL 150 4 Multi-Purpose Headlamp\u003c\/strong\u003e elegantly solves this problem: it attaches directly to the PXE 80 via a PXE clip and illuminates the work surface from the optimal angle — continuously, without occupying a hand.\u003c\/p\u003e\n\u003cp\u003eWith CRI 97 and color temperature adjustment from 2,500K to 6,500K, the \u003cstrong\u003eFLEX MWL 150 4\u003c\/strong\u003e goes far beyond what normal headlamps can do. It's not just a work light for dark corners — it's a precise control instrument that delivers the same color accuracy as professional photo studio lights. For detailing work in vehicle interiors, engine compartments, and tight body parts, this is the crucial difference between a work light and a control tool.\u003c\/p\u003e\n\u003cp\u003eThe multi-purpose function of the \u003cstrong\u003eFLEX MWL 150 4 Multi-Purpose Headlamp\u003c\/strong\u003e makes it the most versatile light in the FLEX portfolio: headband for hands-free work, cap clip for comfortable wearing during longer work phases, PXE clip for mounting on the polisher, and an integrated magnet for temporary attachment to metal parts. Four attachment options, one device — that's an approach that proves its worth in practice.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCRI 97 and 2,500–6,500K — ultimate color rendering in your pocket.\u003c\/strong\u003e With a Color Rendering Index of 97, the MWL 150 4 even surpasses many professional workshop lights. In combination with the stepless color temperature adjustment from warm white (2,500K) to daylight (6,500K), it is the most compact CRI 97 light in the FLEX portfolio. For checking paint subtleties in tight areas — door edges, spoiler undersides, sill areas — this color accuracy is just as crucial as with the large DWL 2500.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePXE clip for direct mounting on the PXE 80 — illuminating the work surface during polishing.\u003c\/strong\u003e The included PXE clip allows the MWL 150 4 to be attached directly to the FLEX PXE 80. The result: the lamp automatically illuminates the current work surface — regardless of the machine's position and without any manual effort. Especially in dark vehicle corners, door cutouts, and under bumpers, this is a significant relief that cannot be achieved as easily with any other lighting solution.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e54g weight, USB-C charging, and integrated magnet — maximum flexibility.\u003c\/strong\u003e At 54g, the MWL 150 4 is so light that it won't be a burden even after hours of wearing it with the headband. USB-C charging allows it to be charged with any modern power supply, laptop, or mobile battery — no proprietary chargers, no additional weight in the toolbox. The integrated magnet allows temporary attachment to metal parts in the vehicle or to workshop equipment — practical for short inspection breaks.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003chr\u003e\n\u003cblockquote class=\"praxistipp\"\u003e\n\u003cp\u003e\u003cstrong\u003eDetailing1 Pro Tip:\u003c\/strong\u003e For interior polishing and tight body areas with the PXE 80, we recommend attaching the MWL 150 4 directly to the polisher via the PXE clip and setting it to 6,500K. The light automatically follows the machine's position and illuminates precisely the area you're working on. After polishing, switch to the headband and use it for the swirl mark check — the same light, two modes of use, zero changeover time.\u003c\/p\u003e\n\u003c\/blockquote\u003e\n\u003chr\u003e\n\u003ch3\u003eCRI 97 in Compact Size — Why Color Rendering Is Crucial Even for Small Lights\u003c\/h3\u003e\n\u003cp\u003eThe CRI 97 value of the \u003cstrong\u003eFLEX MWL 150 4 Multi-Purpose Headlamp\u003c\/strong\u003e is surprising at first glance for a device of this size. In practice, however, it is the most important reason to buy for detailers who are familiar with the CRI demands of the large DWL 2500 and want to maintain this standard for compact work.\u003c\/p\u003e\n\u003cp\u003eWhat CRI 97 means in practice: color tone deviations between body parts after refinishing are recognizable even under this small lamp. Fine holograms in door edges or sill areas — areas that are difficult to reach with large tripods — become visible with the MWL 150 4 in grazing light mode. The combination of high CRI and variable color temperature makes the lamp a full-fledged control tool, not just a work light.\u003c\/p\u003e\n\u003cp\u003eThe comparison with commercially available headlamps is sobering: most cheap headlamps with CRI 70–80 show paint tones slightly distorted and make fine defects invisible. In an area where the result depends on the quality of lighting, this difference is directly relevant to the quality of the work.\u003c\/p\u003e\n\u003cp\u003eThe stepless color temperature adjustment from 2,500K to 6,500K significantly expands the application possibilities. Warm white light for evaluating warm paint colors, neutral light for general work, cool daylight for the final defect check — these functions are fully available even in the small compact lamp.\u003c\/p\u003e\n\u003ch3\u003ePXE Clip and Four Mounting Modes — The Versatility of the MWL 150 4\u003c\/h3\u003e\n\u003cp\u003eThe included \u003cstrong\u003ePXE clip\u003c\/strong\u003e is the most striking feature of the FLEX MWL 150 4 compared to other headlamps. It allows secure attachment directly to the \u003ca href=\"\/fr\/products\/flex-pxe8012ec-akku-exzenterpolierer-80mm-12v\"\u003eFLEX PXE 80 polisher\u003c\/a\u003e — without tape, without improvisation, without restricting machine handling.\u003c\/p\u003e\n\u003cp\u003eIn PXE clip mode, the lamp becomes an integrated work light for the polisher: it always illuminates the current work area, follows the machine, and provides a clear view of the pad and paint — even in areas where the workshop light is insufficient. For detailers who regularly polish in tight vehicle areas — door frames, bumper sections, roof edges — this is a tangible gain in quality and comfort.\u003c\/p\u003e\n\u003cp\u003eThe other three mounting modes expand the application possibilities: the headband turns the MWL 150 4 into a classic headlamp for maintenance work in the engine compartment or for interior inspections in dark vehicle interiors. The cap clip is the more comfortable option for longer work phases without headband pressure. The integrated magnet is suitable for temporary attachment to body parts or tools — for example, when parking the lamp for short work breaks.\u003c\/p\u003e\n\u003cp\u003eThe weight of 54g makes all four modes comfortable: the lamp is barely noticeable, no matter how it is worn. For a 4V LED lamp with CRI 97, variable color temperature, and four attachment options, this is an exceptional packaging density.\u003c\/p\u003e\n\u003ch3\u003eTechnical Features of the MWL 150 4 — 4V Battery, USB-C, and 54g Compact Housing\u003c\/h3\u003e\n\u003cp\u003eThe internal 4V lithium-ion battery of the \u003cstrong\u003eFLEX MWL 150 4\u003c\/strong\u003e can be charged via USB-C, fitting into any modern charging infrastructure. This means: no proprietary charger, no additional adapter, no expensive replacement batteries. If you have USB-C power supplies, power banks, or USB hubs in your workshop, you can charge the MWL 150 4 directly there — a daily convenience that you only appreciate after years of working with proprietary chargers.\u003c\/p\u003e\n\u003cp\u003eThe IP20 protection class is sufficient for indoor and workshop use — the lamp is protected against dust ingress, but not designed for wet work or direct water spray contact. For use on vehicles under normal detailing conditions, i.e., no direct spraying, IP20 is completely acceptable. For outdoor use in rain or during vehicle cleaning, the IP67-protected \u003ca href=\"\/fr\/products\/flex-dwl250012-18-vollspektrum-leuchte\"\u003eDWL 2500\u003c\/a\u003e is recommended.\u003c\/p\u003e\n\u003cp\u003eThe weight of 54g is an important selling point. For a headlamp that is worn for hours, weight is the most important comfort factor — and 54g is far more comfortable than the 150–250g that many professional headlamps weigh. Even when mounted on the PXE clip, where the weight affects machine handling, 54g is barely noticeable.\u003c\/p\u003e\n\u003cp\u003eThe two brightness levels (75 lm and 150 lm) cover different application scenarios: 75 lm for continuous operation during polishing, 150 lm for the grazing light inspection check. The compact dimensions of 95 × 27 × 27mm fit into any toolbox and take up hardly any space during transport. The lamp is therefore an everyday companion that is always with you — not the heavy special tool that you only get out when needed.\u003c\/p\u003e\n\u003ch3\u003eMWL 150 4 in Comparison — Compact Headlamp vs. Dedicated Workshop Lights\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003eFLEX MWL 150 4\u003c\/strong\u003e is not designed as a replacement for the \u003ca href=\"\/fr\/products\/flex-dwl250012-18-vollspektrum-leuchte\"\u003eDWL 2500\u003c\/a\u003e — it is a supplement for tasks where the DWL 2500 is too large and bulky. The comparison between the two lights is therefore not an either\/or, but a both\/and.\u003c\/p\u003e\n\u003cp\u003eThe DWL 2500 delivers 3,000 lumens over a large area and is suitable for overall vehicle inspection from a tripod. The MWL 150 4 delivers 150 lumens to a precise, small area and is suitable for close-up work, tight areas, and PXE 80 operation. Those who have both lights have a complete lighting solution for all phases of vehicle detailing — from large-area rough inspection to detailed spot control in body seams and door edges.\u003c\/p\u003e\n\u003cp\u003eCompared to generic headlamps from electronics retailers, the MWL 150 4 is clearly superior in two respects: CRI 97 instead of CRI 70–80 and the PXE clip function. The latter is unique in the market — no other headlamp is specifically designed for mounting on the FLEX PXE 80. For detailers who use the PXE 80 daily, this is a unique functional selling point without competition.\u003c\/p\u003e\n\u003ch3\u003eBuying the FLEX MWL 150 4 — Who Benefits from the Multi-Purpose Headlamp?\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003eFLEX MWL 150 4 Multi-Purpose Headlamp\u003c\/strong\u003e is recommended for all PXE 80 users who regularly polish in poor lighting conditions. As a dedicated accessory for the PXE 80, it belongs to the polisher's natural expansion set — alongside the DT adapter and the BP-M PXE hook-and-loop pad, the MWL 150 4 is the most practical addition for daily polishing work.\u003c\/p\u003e\n\u003cp\u003eFor all detailers who perform interior work, engine compartment inspections, or work in dark underbody areas, the MWL 150 4, as a freestanding headlamp with CRI 97, is a significant upgrade over cheaper alternatives. The light is accurate enough to reliably assess paint tones — even indoors without daylight.\u003c\/p\u003e\n\u003cp\u003eThe device comes with a USB-C cable and all four attachment accessories — headband, cap clip, PXE clip, and magnet. No separate battery needed, no charger — just connect it via USB-C to your existing charging infrastructure. For professional detailers and enthusiasts with a PXE 80, the \u003cstrong\u003eFLEX MWL 150 4 Multi-Purpose Headlamp\u003c\/strong\u003e is one of the most affordable ways to meaningfully expand your detailing setup's lighting arsenal — with the advantage that it serves not only as an accessory for the PXE 80 but also as a full-fledged inspection and work light for all other everyday workshop applications.\u003c\/p\u003e","brand":"FLEX","offers":[{"title":"MWL 150 4 \"534476\"","offer_id":57377625276751,"sku":"D1-FLEX-534476","price":89.89,"currency_code":"EUR","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0800\/3272\/7375\/files\/flex-mwl-150-4-mehrzweck-stirnlampe-mwl-150-4-534476-534476.png?v=1775059113"},{"product_id":"flex-tl4000-led-baustrahler-stativ-18v","title":"\"TL 4000 18.0\/230\" projecteur LED sur trépied (18V)","description":"\u003ch2\u003eLED Work Light with Dual-Power — the FLEX TL 4000 18.0\/230 for Workshop and Detailing\u003c\/h2\u003e\n\u003cblockquote\u003e\n\u003cp\u003e\u003cem\u003eWhat is the FLEX TL 4000 18.0\/230? The FLEX TL 4000 18.0\/230 is a professional LED work light with a tripod — dual-power from an 18V battery or 230V mains, 4000 lumens in three stages, height-adjustable tripod from 1.1 to 2.2 meters for detailing, workshops, and mobile use.\u003c\/em\u003e\u003c\/p\u003e\n\u003c\/blockquote\u003e\n\u003chr\u003e\n\u003cp\u003eWork light that is truly sufficient — not just bright enough, but bright enough for the most demanding task in vehicle detailing: paint inspection. The \u003cstrong\u003eFLEX TL 4000 18.0\/230 LED work light\u003c\/strong\u003e delivers up to 4000 lumens of neutral white 4000 K light, making swirls, scratches, and paint defects visible that remain hidden under normal workshop lighting. The tripod positions the light precisely at working height — continuously adjustable from 1.1 to 2.2 meters — and the three-part lamp head can be swiveled on both axes until the light beam is exactly where it is needed.\u003c\/p\u003e\n\u003cp\u003eThe decisive feature of the TL 4000 18.0\/230 is its dual-power operation: the light runs either on a \u003ca href=\"\/fr\/products\/flex-pset55r-akku-set-18v\"\u003eFLEX 18V battery pack\u003c\/a\u003e or directly from a 230V socket via a standard cold device cable. Those who work mobile — on-site with customers, at a vehicle event, or outdoors — use the battery and are independent of power outlets. Those who work in their own workshop simply plug in the power cord and save the battery for other devices. This flexibility is not a luxury in professional detailing, but a reality of work.\u003c\/p\u003e\n\u003cp\u003eThe FLEX TL 4000 18.0\/230 is aimed at detailers and reconditioners who perform professional paintwork under controlled lighting conditions: swirl inspection after polishing, quality control after ceramic sealing, paint correction in poorly lit workshops, mobile detailing assignments without a power outlet, and daily workshop operations where good work light prevents errors before they occur.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e4000 lumens in three stages — maximum brightness for professional paint inspection.\u003c\/strong\u003e The 4000-lumen stage of the TL 4000 delivers a light intensity that is rarely surpassed in detailing. For swirl inspection before and after paint correction, this amount of light is crucial: fine holograms and micro-scratches only become visible under sufficiently strong, targeted work light. The 1000 and 2000-lumen stages cover lighter tasks — general workshop lighting, interior work, and situations where battery capacity needs to be conserved.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDual-Power 18V + 230V — cordless mobile or permanently on mains, without changing devices.\u003c\/strong\u003e As the only light in the FLEX range, the TL 4000 combines the cordless freedom of the 18V battery system with the unlimited operating time of a mains connection. The standard cold device cable (sold separately) makes the light independent of the battery — at a fixed workshop station, mains operation is the more economical choice because the \u003ca href=\"\/fr\/products\/flex-pset55r-akku-set-18v\"\u003eFLEX P-Set 55 R battery pack\u003c\/a\u003e remains reserved for the polishing machine.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHeight-adjustable tripod 1.1–2.2 m with three-part swivel head — precise light positioning.\u003c\/strong\u003e The integrated tripod optimally positions the light in every work situation: low for sill work and underbody inspection, high for the roof and hood. The three-part lamp head with two-axis swiveling allows precise alignment of the light beam to any body point. For gloss level control after polishing, this adjustability is more important than the raw lumen count — only with the correct angle of incidence do paint defects become visible.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003chr\u003e\n\u003cblockquote class=\"praxistipp\"\u003e\n\u003cp\u003e\u003cstrong\u003ePractical tip from Detailing1:\u003c\/strong\u003e Position the TL 4000 18.0\/230 at a medium height (approx. 1.5 m) and with a flat angle of incidence to the vehicle side — this is the most effective angle for swirl inspection. Grazing light makes holograms and polishing marks visible that remain hidden under direct light. After paint correction, set the light to 4000 lumens and systematically guide it over the body from back to front: only when the vehicle looks clean in this light is the polishing work truly complete. For mains operation, have a cold device cable (IEC C13) ready — this saves the battery for polisher and heat gun.\u003c\/p\u003e\n\u003c\/blockquote\u003e\n\u003chr\u003e\n\u003ch3\u003e4000 Lumens and 4000 K Neutral White — why light quality is crucial in detailing\u003c\/h3\u003e\n\u003cp\u003eNot every light shows paint defects equally well. The light temperature — measured in Kelvin — influences how well the human eye recognizes fine surface structures. The \u003cstrong\u003eFLEX TL 4000 18.0\/230\u003c\/strong\u003e operates at 4000 Kelvin, which is described as neutral white and is positioned between warm halogen yellow (2700–3000 K) and cool daylight (5500–6500 K). In practice, this means that the light produces a clear but not dazzlingly harsh light that reproduces paint colors naturally while sharpening contrasts for defect detection.\u003c\/p\u003e\n\u003cp\u003eThis compromise is ideal for paint correction: warm white light overpowers fine swirls because it creates hardly any contrasts. Cool white daylight is high-contrast but distorts paint colors and makes color assessment after sealing difficult. 4000 K hits the mark: clearly visible paint structure with color-accurate representation. For detailers who assess ceramic coatings by application — i.e., control the even curing film — neutral white is the right color temperature.\u003c\/p\u003e\n\u003cp\u003eThe three brightness levels of the TL 4000 (1000 \/ 2000 \/ 4000 lm) complement the high light quality with practical step control. For rough inspection or interior work, 1000 lm is sufficient without unnecessarily burdening the battery. 2000 lm is the all-round level for general workshop lighting. 4000 lm is used for critical paint inspection — when every detail counts and no defect can be overlooked. This gradation significantly extends battery life: operating the TL 4000 at 1000 lm provides significantly more time per charge cycle than at full load.\u003c\/p\u003e\n\u003cp\u003eFor comparison: commercially available workshop lights often operate with 800–1500 lm and warm white light. The TL 4000 delivers 2.5 to 5 times this performance at the highest level — with superior color temperature. For professional detailing results, this difference is measurable in the quality of the work delivered.\u003c\/p\u003e\n\u003ch3\u003eDual-Power in everyday work — 18V battery or 230V mains depending on the situation\u003c\/h3\u003e\n\u003cp\u003eThe dual-power capability of the \u003cstrong\u003eFLEX TL 4000 18.0\/230\u003c\/strong\u003e is more than a technical feature — it is a response to the practical reality of professional detailing. No detailer works exclusively in their own workshop, and no detailer always has a power outlet at hand. The TL 4000 is designed for both situations: cordless with the \u003ca href=\"\/fr\/products\/flex-pset1888r-akku-set-xlithium-18v\"\u003eFLEX P-Set 18-88 R XLITHIUM battery pack\u003c\/a\u003e for maximum runtime without an outlet, or via cold device cable to the 230V mains for unlimited continuous operation in the workshop.\u003c\/p\u003e\n\u003cp\u003eIn battery operation, the runtime depends on the selected brightness level and the battery capacity used. With the \u003ca href=\"\/fr\/products\/flex-pset55r-akku-set-18v\"\u003e5.0 Ah pack from the P-Set 55 R\u003c\/a\u003e and the medium brightness level (2000 lm), the TL 4000 easily achieves a runtime of 1–2 hours — sufficient for a complete vehicle inspection. For longer outdoor use, the 8.8 Ah pack from the P-Set 18-88 R is recommended, which extends the runtime accordingly. The advantage of the FLEX 18V system: every battery pack that runs on the polisher also runs in the TL 4000 — no separate battery system, no separate purchase costs.\u003c\/p\u003e\n\u003cp\u003eIn mains operation, any battery considerations are completely eliminated. A standard cold device cable (IEC C13 — the standard connection for computers and coffee machines, available in any electronics store) turns the TL 4000 into a stationary continuous light. For workshops with a fixed foiling or polishing station, mains operation is the most economical configuration: no battery charging effort, no runtime planning, no risk of interruption. The TL 4000 simply runs as long as the workshop is open.\u003c\/p\u003e\n\u003cp\u003eThe dual-power feature is particularly valuable for detailers who offer both: mobile assignments at the customer's site (with battery) and workshop work in their own business (with mains). Instead of buying two lights — one for mobile, one for the workshop — a single TL 4000 is sufficient for both applications. This reduces investment costs and significantly simplifies equipment organization.\u003c\/p\u003e\n\u003ch3\u003eTripod and lamp head — professional light positioning for bodywork and interior\u003c\/h3\u003e\n\u003cp\u003eA construction spotlight without an adjustable tripod is hardly usable for professional detailing — the correct light position makes the difference between a visible paint defect and an overlooked dent. The integrated tripod of the \u003cstrong\u003eFLEX TL 4000 18.0\/230\u003c\/strong\u003e is continuously adjustable from 1.1 to 2.2 meters. This range covers practically all relevant work situations: 1.1 meters for sill areas, door sills and lower doors, 1.6–1.8 meters for sides and hood, 2.2 meters for roof and high-mounted spoilers.\u003c\/p\u003e\n\u003cp\u003eThe lamp head itself consists of three individually swiveling panels on two axes. This means: the light can be used as a floodlight that illuminates a wide area evenly, or as a directed spotlight that is aimed precisely at a body point. For swirl inspection, flat, grazing light is the right technique — here, the panels are aligned parallel to the vehicle side, so that the light sweeps flat over the surface and makes scratches visible by creating shadows. For interior lighting, the panels are tilted inwards and focus the light on the passenger compartment.\u003c\/p\u003e\n\u003cp\u003eThe dimensions of the light (1190 × 295 × 275 mm assembled, weight 8.2 kg without battery) are appropriate for a professional work light of this class. The tripod can be folded for transport and storage, which makes mobile use practical. The weight of 8.2 kg is transportable, but not a device for frequent one-man quick transports — for mobile assignments to the customer, a stable transport case or carrying bag is recommended.\u003c\/p\u003e\n\u003cp\u003eThe \u003ca href=\"\/fr\/products\/flex-wls70190-mobiles-leuchten-stativ\"\u003eFLEX WLS-70-190 Mobile Light Tripod\u003c\/a\u003e is an additional option for workshops that frequently need to reposition their TL 4000 — the separate tripod with wheels simplifies quick repositioning without complete reassembly. In combination with the TL 4000, the WLS-70-190 is the professional workshop solution for detailers who inspect multiple vehicle sides in one work step.\u003c\/p\u003e\n\u003ch3\u003eComparison TL 4000 vs. DWL 2500 and WL 1000 — which FLEX LED light for which purpose\u003c\/h3\u003e\n\u003cp\u003eThe FLEX lighting portfolio offers several options for detailing. In a direct \u003cstrong\u003ecomparison\u003c\/strong\u003e between the \u003cstrong\u003eFLEX TL 4000 18.0\/230\u003c\/strong\u003e, \u003ca href=\"\/fr\/products\/flex-dwl25001218-led-vollspektrum-leuchte\"\u003eDWL 2500 12\/18 LED Full-Spectrum Light\u003c\/a\u003e, and \u003ca href=\"\/fr\/products\/flex-wl100018-led-akku-strahler-18v\"\u003eWL 1000 18.0 LED Battery-Powered Spotlight\u003c\/a\u003e, clear differences emerge that depend on the specific application profile.\u003c\/p\u003e\n\u003cp\u003eThe TL 4000 18.0\/230 is the choice for area lighting and professional paint inspection on the entire vehicle. The 4000 lumens, the tripod, and the swivel three-panel lamp head make it the most powerful work solution when it comes to fully illuminating an entire vehicle. Dual-power operation and the tripod height of up to 2.2 m are unique selling points that none of the smaller lights offer.\u003c\/p\u003e\n\u003cp\u003eThe DWL 2500 12\/18 is a full-spectrum light for special applications: full-spectrum light (high CRI value) is particularly suitable for color assessment because it reproduces paint colors similarly to natural daylight. For paint professionals or detailers who assess color corrections, the DWL 2500 is the more precise choice. With 2500 lumens, it is brighter than the WL 1000, but weaker than the TL 4000 — and it has no tripod, which limits its direct use.\u003c\/p\u003e\n\u003cp\u003eThe WL 1000 18.0 is the compact, handy version for targeted spot lighting: individual body areas, interior inspections, and small work areas. With 1000 lumens and no tripod, it is the quickly deployable addition, not a main solution for complete vehicle inspection. In combination with the TL 4000 as the main light, the WL 1000 is ideal for targeted follow-up inspections of individual areas.\u003c\/p\u003e\n\u003cp\u003eFor a fully equipped detailing workshop, we recommend: TL 4000 as the main work light for paint inspection and area lighting, WL 1000 as a handy auxiliary light for targeted spot applications. This combination covers all relevant lighting tasks.\u003c\/p\u003e\n\u003ch3\u003eBuy FLEX TL 4000 18.0\/230 — the professional lighting system for demanding detailers\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003eFLEX TL 4000 18.0\/230 LED work light\u003c\/strong\u003e is the professional main light for detailers and reconditioners who accept no compromises in paint inspection. The combination of 4000 lumens in neutral white, the height-adjustable tripod, and the dual-power operation from battery and mains makes the TL 4000 the most versatile work light in the FLEX range — for the fixed workshop as well as for mobile use.\u003c\/p\u003e\n\u003cp\u003eThe device is available without battery and charger (SKU D1-FLEX-530375) — for all those who are already in the FLEX 18V system and use existing battery packs. Those new to the FLEX 18V system combine the TL 4000 with the \u003ca href=\"\/fr\/products\/flex-pset55r-akku-set-18v\"\u003eP-Set 55 R battery set\u003c\/a\u003e for immediate use. The 5.0 Ah pack from the P-Set 55 R is the recommended main solution for work light operation: sufficient capacity for long work sessions during paint inspection, and reusable directly on the polisher after use on the work light.\u003c\/p\u003e\n\u003cp\u003eFor battery management, we recommend using the \u003ca href=\"\/fr\/products\/flex-whp-wandhalter-haken\"\u003eFLEX WHP wall mount\u003c\/a\u003e: all battery packs of the 18V system are simultaneously charged and ready at the workshop wall — work light, polisher, and heat gun share the same battery pool. All packs charged in the morning, rotation between devices during the day without charging interruptions. This is the FLEX 18V system in its complete, efficient form.\u003c\/p\u003e\n\u003cp\u003eAnyone who delivers professional paintwork must also be able to recognize professional paint defects. The TL 4000 18.0\/230 is the tool that makes swirls, holograms, and inclusions visible — even those that remain hidden under normal workshop lighting. It is not an accessory, but an integral part of the professional detailing workstation.\u003c\/p\u003e","brand":"FLEX","offers":[{"title":"TL 4000 18.0\/230 \"530375\" (Battery\/charger not included)","offer_id":57377625375055,"sku":"D1-FLEX-530375","price":291.89,"currency_code":"EUR","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0800\/3272\/7375\/files\/flex-tl-4000-18-0-230-led-baustrahler-mit-stativ-18v-tl-4000-18-0-230-530375-530375.png?v=1775059239"}],"url":"https:\/\/detailing1.co\/fr\/collections\/beleuchtung.oembed","provider":"Detailing1","version":"1.0","type":"link"}